Bedienungsanleitung Satel CA-6 (Seite 8 von 40) (Englisch)

699578

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

6 Programming CA-6

EXAMPLE:

changing the service code from 12345 to 78901

[12345] [#] - enter the service mode

[1] [#] - call the service function 1

[78901] [#] - enter the new code and confirm it; the function will be automatically exited

FS2 - programming control panel password (HEX)

FS3 - programming computer password (HEX)

In the DOWNLOADING mode (see: Installer Manual), the control panel, having

established connection with the computer, sends a six-character panel password and

waits for the password (identifier) of the answering computer. When the appropriate

identifier is received, the transmission to computer can begin. On receiving an identifier

other than that programmed with this function, the control panel will hang up. The

control panel will accept no command from the computer, unless the computer identifier is

valid.

Programming of this identifiers consists in entering three pairs of hexadecimal characters

(digits from 0 to 9 and characters A, B, C, D, E, F - see the table of codes), in the following

order: [first][second][#], [third][fourth][#], [fifth][sixth][#]. The LEDs at first display previous

settings, and, after the change – the values of entered characters (binary, the first

character - LEDs 1 to 4, the second – LEDs 5 to 8, number of programmed characters

pairs - LEDs AB, AB). Having entered the last pair of characters, the panel automatically

exits the function.

EXAMPLE:

programming the identifier 23C4D5

[12345] [#] - enter service mode

[2] [#] - call the required function

[2][3] [#] - enter the two first characters

[

2][4] [#] - enter the two next characters

[

3][5] [#] - enter the two last characters; after acknowledging them the panel will automatically exit

the function

The factory identifiers can be restored with function FS109.

FS4 - programming computer telephone number (HEX)

The computer telephone number is necessary for initiating communication from the control

panel keypad (user function “0”). When communication is initiated from the computer, the

panel, after the communication passwords exchange, hangs up and calls back the

computer. If the computer telephone number is not programmed, it is possible to initialize

the communication from the computer in a simplified way - the control panel will not hang

up and call back.

The telephone number can consist up to sixteen digits and special characters. The special

characters are used to control the dialing process. Telephone number is programmed by

entering the consecutive digits and characters in pairs. Each pair is to be confirmed by the

[#] key (see the example below). The LEDs AB, AB show (binary) which pair of characters

is being programmed, and the LEDs 1-4 and 5-8 show (also binary) the values of

programmed digits.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Satel CA-6 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Satel CA-6

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info