Bedienungsanleitung Satel CA-6 (Seite 11 von 40) (Englisch)

699578

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

CA-6 SATEL 9

THIRD SET – the lower A and B diodes are blinking

No LED Option

downloading unavailable if any partition is armed

OFF

downloading always available

alarm if zones are violated after the exit delay elapses

OFF

control panel does not alarm if zones in partition are violated after the exit delay

elapses

OUT4 and OUT5 outputs work in „UA” format

OFF

OUT4 and OUT5 outputs work in PC16OUT format

Note: The options: 1,4,5,6 and 8 from the third set of options are irrelevant in the CA-6.

FS6 - programming the global times (DEC)

The settings refer to the entry delay, exit delay and alarm time. The times are valid for the

entries and exits to which no individual times are assigned. The exit delay time is

common for all partitions. In case of the entry delay time it is possible to program an

individual delay for each zone and In case of the alarm time it is possible to program

a separate time for each output. The alarm time programmed in this function refers also to

the keypad alarm signaling.

Note: The alarm time set with the function FS6 defines also the zone alarms blocking

time - when the alarm is on, the subsequent zone violations will not trigger

consecutive alarms until the blocking time elapsed.

Programming the times is carried out in the following order:

- entry delay (from 00 to 99 seconds ) - the lower B diode is blinking,

- exit delay (from 00 to 99 seconds) - the lower A diode is blinking,

- alarm time (from 00 to 99 seconds) - the A and B diodes are blinking.

EXAMPLE:

programming the times: entry delay=30s, exit delay=60s, alarm=90s

[12345] [#] - enter the service mode

[6] [#] - call the required function

[3][0] [#] - enter the entry delay time (two digits) – the lower B LED is blinking

[6][0] [#] - enter the exit delay time (two digits) – the lower A LED is blinking

[9][0] [#] - enter the alarm time – the A and B LEDs are blinking - after acknowledging the last

settings, the control panel automatically exits the function

FS7 - programming the counting zone counters (DEC)

The control panel is equipped with three independent violation counters which can be

associated with any zones. Violation of these zones triggers an alarm after the

programmed number of violations is exceeded. All the violations must occur within

a specific period of time. Each counter can sum up violations of one or several zones

defined as the counting zones (e.g. the counter 1 can count violations of zone 2, the

counter 2 - violations of zones 4, 5, 6). The alarm will be generated by the zone which has

been violated as the last one.

Three counter values are programmed, from 01 to 07, in the following order: counter 1,

counter 2, counter 3. If no counting zones are provided in the panel, the programmed

values are irrelevant.

If "00" has been programmed, the counting zone will operate as the instant one.

Count times of the counters are programmed in FS123.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Satel CA-6 Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Satel CA-6

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info