Bedienungsanleitung Satel CA-6 (Seite 12 von 40) (Englisch)

699578

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

10 Programming CA-6

EXAMPLE:

programming the counters: the 1

- 2 violations, the 2

- 5 violations, the 3

- without

changes

[12345] [#] - enter the service mode

[7] [#] - call the required function

[0][2] [#] - program the first counter (the lower B LED is blinking)

[0][5] [#] - program the second counter (the lower LED A is blinking)

[

] - exit the function - programming of the third counter is omitted

In case of programming three counters, the function is automatically exited after the third

counter

Functions programming assignment

FS8 - programming A partition zones (BIT)

FS9 - programming B partition zones (BIT)

The functions FS8 and FS9 are used to divide the alarm system into partitions.

It is possible to assign any zone to the partitions. Independent sirens and messaging

telephone numbers can be assigned to the partitions, and separate access codes can be

programmed – thus creating two independent alarm systems.

Optionally, the so-called interior partition can also be created (if one partition is to be fully

contained in the other).

When both partitions are armed, it is possible to disarm the interior partition by

using its code. The other zones, which belong to the primary partition, will remain

armed.

Note: If the armed mode is activated by means of the primary partition code, the interior

partition zones will be automatically armed as well, but their status as a partition

status will not be signaled by the control panel – the

[

ARMED

] LED, which

corresponds to the interior partition, is "off".

A zone can be assigned to both partitions at the same time. The common zone will only be

armed, when both partitions are armed (if the partitions do not contain one another, i.e. the

partition is not the interior one).

Zones can be assigned to the partition by pressing the keys 1 to 8, which is shown by

lighting of the LED which indicates the respective zone. Use the [#] key to confirm the

selection and exit the function. Use the [

] key to interrupt the programming.

FS16 - programming auto bypassed zones in A partition (BIT)

The AUTO BYPASS function applies to the zones which are automatically bypassed after

arming with the 7 authority level code (partial arming), assigned to the A partition. The

same zones are bypassed after silent arming of the A partition.

The control panel permits also programming another set of automatically bypassed zones:

bypassed when no exit from the partition (EXIT-BYPASS zones - with service functions

FS127, FS128).

The programming is similar to the programming of FS8 function. After the corresponding

diodes are turned on the [#] key should be pressed.

FS17 - programming bypassed zones in B partition (BIT)

The function refers to the automatically bypassed zones in B partition. The programming

as in FS16.

FS20 - programming keypad and partition options (BIT)

Some of the user functions and the keypad beeps are optional. The FS20 function defines

which of them are to be performed.

Two sets of options are programmed, each of them need to be confirmed with the [#] key.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Satel CA-6 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Satel CA-6

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info