Bedienungsanleitung Satel CA-6 (Seite 14 von 40) (Englisch)

699578

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

12 Programming CA-6

Functions programming zone parameters

FS24 - programming zone sensitivity

Each zone of the CA-6 can have an individual reaction time. Violations lasting shorter than

the programmed reaction time are disregarded by the control panel. Programming the

zones sensitivity in keypad is performed in a different way, than programming the other

parameters. The programming includes values from 1 to 255 which corresponds to the

times from 16 ms to 4080 ms according to the formula:

REACTION TIME = PROGRAMMED VALUE x

16 ms

By default, all the zones have the same reaction time (480 ms). In most cases, no change

of the time setting is required.

The function is intended for advanced installers. It allows the zone sensitivity to be

selected when special detectors are used (for example, mechanical glass break detectors,

or low hysteresis detectors, not fitted with monovibrator at the output).

Note: The minimum keypad zones sensitivity is 64ms (4 x 16 ms). The actual

sensitivity values of these zones can amount to n x 64ms (n=1,2,3,...). This

results from the way the keypad is operated by the control panel – the

zones status is read out at 64ms intervals.

During programming, the AB, AB LEDs indicate which zone the parameter refers to. The

zone number is displayed in binary format (for zone no. 1 – the lower B LED is blinking, for

zone no. 2 – the lower A LED, for zone no. 3 – both of them, etc.).

After setting a value for the given zone, press the [#] key to proceed to programming the

reaction time of the next zone. After the last parameter is entered and confirmed, the

control panel exits the function. The introduced changes will only be displayed after the

function is reentered.

The programming can be interrupted by using the [

] key.

EXAMPLE:

changing the reaction time of zones 1, 3 and 6 to 800 ms, zone 8 to 100 ms, the other

zones unchanged

800 ms/16 ms = 50 (enter this value for zones 1,3 and 6)

100 ms /16 ms = 6.25 (enter 6 for zone 8, it will ensure the reaction time = 96 ms)

[12345] [#] - enter the service mode

[2][4] [#] - call the function

[5][0] [#] - reaction time for the first zone (AB, AB LEDs = 0001)

[#] - confirm the second zone time (AB, AB LEDs = 0010)

[5][0] [#] - reaction time for the third zone (AB, AB LEDs = 0011)

[#] - confirm the fourth zone time (AB, AB LEDs = 0100)

[#] - confirm the fifth zone time (AB, AB LEDs = 0101)

[5][0] [#] - reaction time for the sixth zone (AB, AB LEDs = 0110)

[#] - confirm the seventh zone time (AB, AB LEDs = 0111)

[6] [#] - reaction time for the eighth zone (AB, AB LEDs = 1000)

the control panel automatically exits the function

Note: The parameter is entered in decimal and indicated in binary format.

A new value can be checked only after reentering function. It is displayed in binary format

on LEDs from 1 to 8.

The LEDs which are off mean 0. The value of the LEDs which are on corresponds with the

table below:

LED number 1 2 3 4 5 6 7 8

Bit weight 128 64 32 16 8 4 2 1

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Satel CA-6 Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Satel CA-6

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info