Bedienungsanleitung Satel CA-6 (Seite 27 von 40) (Englisch)

699578

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

CA-6 SATEL 25

FS85 - programming test transmission time (DEC)

The function sets three time parameters which define the moments of sending the test

transmission code to the monitoring station.

The first parameter (two two-digit numbers: hours, minutes) enables the station to check if

the control panel clock works properly. The mechanism sending the code every day at the

same time can be disabled by programming a wrong time (for example, 99.99).

The second parameter (three two-digit numbers: number of days, hours, minutes) defines

the time counted from the last transmission to the station, after which test code will be sent

by the control panel. After occurrence in the system of any event whose code will be sent,

the panel starts counting the time again. This mechanism can be disabled by programming

00.00.00.

The third parameter (three two-digit numbers: number of days, hours, minutes) makes it

possible to program a separate period of the test transmission, valid only when the system

is armed (for example, when more frequent test transmissions are needed during the

armed mode). The control panel, when system is armed, calls the monitoring station every

period of time specified in the given function. If a new event occurs and the panel sends

its’ code to the monitoring station, then the countdown of the programmed time starts from

the beginning. When 00, 00, 00 value is entered, then, irrespective of whether the control

panel is armed or not, only the time programmed in FS 70 is used.

The programming consists in entering five two-digit numbers. After confirmation of all the

numbers, the panel exits the function.

EXAMPLE: programming the test code to be sent at 1:45 (clock test) and after two hours since the

last transmission (communication test), communication test, when system is armed –

every 15 min.

[12345] [#] - enter the service mode

[8][5] [#] - call the function

[0][1] [#] - enter the hours

[4][5] [#] - enter the minutes of clock test time (sending the message)

[0][0] [#] - enter the number of days,

[0][2] [#] - enter the number of hours,

[0][0] [#] - enter the number of minutes of the communication test time.

[0][0] [#] - enter the number of days

[0][0] [#] - enter the number of hours

[1][5] [#] - enter the number of minutes of the communication test during arm mode and terminate

the function

Note: If the test transmissions are conducted frequently (e.g. every 10 – 15 min.), it is

recommended to activate in function FS5 option number 5 of the first set. Thus

preventing the events memory of the control panel from being quickly filled up, since

only 3 successive events of the test transmission are then saved in memory of the

control panel.

FS86 - programming the „AC loss” report delay (DEC)

The function defines the time from the mains supply loss after which the panel will send an

„AC loss” message to the monitoring station. The delay time is programmed in minutes,

within the range from 01 to 99 minutes. The mains supply loss is signaled instantly in

keypads and on the AC

POWER LOSS

indicator outputs (function 25).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Satel CA-6 Seite 27

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Satel CA-6

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info