Bedienungsanleitung Satel CA-6 (Seite 28 von 40) (Englisch)

699578

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

26 Programming CA-6

Messaging – programming telephone number

FS87 - programming telephone number 1 (HEX)

FS88 - programming telephone number 2 (HEX)

FS89 - programming telephone number 3 (HEX)

FS90 - programming telephone number 4 (HEX)

The functions FS87 to FS90 are used to program the telephone numbers to which the

control panel sends alarm messages. Each telephone number can have up to sixteen

digits and special characters. The numbers are to be programmed in the same way as in

the function FS4.

FS95 - programming assignment of partitions and messages (BIT)

At the moment an alarm occurs, the control panel can send an alarm message to four

telephone numbers. As the system can be divided into independent partitions, the

messaging should depend on which partition is alarming. The FS95 function assigns the

telephone numbers to partitions and defines which message is to be sent.

To program this parameter it is necessary to assign partition and number of message,

which is to be sent to each telephone number. The AB, AB LEDs indicate (in binary

format) the telephone number, which is being programmed.

The LEDs 1 and 2 show the assignment of consecutive numbers to partitions:

1 - telephone number for A partition

2 - telephone number for B partition

A telephone number can be associated with one or two partitions.

The LEDs 5 to 6 show the message, which is sent to a consecutive number:

5 - message 1 to pager

6 - message 2 to pager

Note: If no message for the paging system is assigned to the number, the panel will

send a voice message from the synthesizer.

EXAMPLE:

programming of the following settings (assuming that LEDs 1 to 8 for all numbers are off)

● 1

telephone number - message no. 1 (pager), in case of alarm in A & B partitions,

● 2

telephone number - message no. 2 (pager), in case of alarm in A partition,

● 3

& 4

tel. number - voice message from synthesizer, in case of alarm in B partition.

[12345] [#] - enter the service mode

[9][5] [#] - call the function (lower B diode is blinking - 1

telephone number)

[1] - LED 1 goes on (number 1 assigned to A partition)

[2] - LED 2 goes on (number 1 assigned to B partition)

[5] - LED 5 goes on (message 1 assigned to number 1)

[#] - confirm assignment for number 1 (A LED is blinking - 2

number)

[1] - LED 1 goes on (number 2 assigned to A partition)

[6] - LED 6 goes on (number 2 assigned to B partition)

[#] - confirm assignment for number 2 (A and B LEDs are blinking- 3

number)

[2] - LED 2 goes on (number 3 assigned to B partition)

[#] - confirm assignment for number 3 (upper B LED is blinking - 4

number)

[2] - LED 2 goes on (number 4 assigned to B partition)

[#] - confirm assignment for number 4

Messaging – programming of PAGER messages

FS96 - programming message 1 (POLPAGER format)

FS97 - programming message 2 (POLPAGER)

The message is programmed in the same way as in case of direct telephone messaging to

the POLPAGER receiver. The control panel saves in its memory the consecutively

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Satel CA-6 Seite 28

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Satel CA-6

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info