Bedienungsanleitung Satel CA-6 (Seite 30 von 40) (Englisch)

699578

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

28 Programming CA-6

FS101 - programming number of rings before answer (DEC)

The function sets the number of rings after which the CA-6 control panel answers the call

in order to report the alarm system status or to establish communication with the

computer. The programming consists in entering a number from 01 to 15 and confirming it

with the [#] key.

Depending on how the answering option is set (the FS5 function, the second set of

options), the control panel will answer the call immediately after detecting the programmed

number of rings, or on the first ring detected after an interval lasting less than 5 minutes

from detecting the programmed number of rings ("double call").

Notes:

• Having answered a call in the "single call" mode, the panel will not answer any more

calls for about 5 minutes so as to enable access to other equipment connected after

the panel (e.g. automatic answering system, fax/modem).

• When it is impossible to establish communication with the control panel by the

computer, and the call answering is on, the control panel will only answer the calls

when all defined partitions are armed.

Functions programming TIMERS

The CA-6 control panel is equipped with four TIMERS, which compare the panel clock with

the times set on the TIMERS. If the times are consistent, the timers perform the functions

assigned to them.

FS102 - programming TIMERA 1 (DEC)

The function defines the TIMER 1 ON/OFF hour and minute. The programming consists in

entering four two-digit numbers, the first two denoting the ON time (hour, minute), and the

other two the OFF time (hour, minute). If you want to program the ON or OFF time only

than set one of the times at 99:99 value.

EXAMPLE:

programming the TIMER 1: ON time - 16:30, OFF time - 06:30

[12345] [#] - enter the service mode

[1][0][2] [#] - call the function

[1][6] [#] - program the ON time hours (B LED is blinking)

[3][0] [#] - program the ON time minutes (A LED is blinking)

[0][6] [#] - program the OFF time hours (A & B LEDs are blinking)

[3][0] [#] - program the OFF time minutes and exit the function (B LED is blinking)

FS103 - programming TIMERA 2 (DEC)

FS104 - programming TIMERA 3 (DEC)

FS105 - programming TIMERA 4 (DEC)

FS106 - programming TIMER functions (DEC)

The function defines how the timers are used. They can control outputs or partitions.

The programming consists in entering four characters from 0 to 9 (2× two characters). The

first character defines the TIMER 1 function, the second - TIMER 2, the third - TIMER 3,

and the fourth - TIMER 4.

Note: The outputs indicated in this function, irrespective of their type, are controlled by

TIMER – as distinct from the CA-10 control panel, where the timers control only

the TIMER type outputs.

TIMER functions:

0 - TIMER not used

1 - controls output OUT1

2 - controls output OUT2

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Satel CA-6 Seite 30

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Satel CA-6

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info