Bedienungsanleitung Satel INT-TSG-BSB (Seite 14 von 28) (Englisch)

699393

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

12 INT-TSG SATEL

7 – trouble status [Troubles] – if this option is enabled, you can view the current troubles

without entering the code:

– after tapping on the “System status” screen,

– after tapping and holding for 3 seconds on the terminal.

8 – chime on/off [Chime changing] – if this option is enabled, the user can switch on/off the

CHIME signal in the keypad by means of the terminal, tapping and holding for about 3

seconds on the terminal.

Zone state [Zone characters] – you can define the symbols which will be used by the

terminal to illustrate the state of zones.

Partition state [Part. characters] – you can define the symbols which will be used by the

terminal to illustrate the state of partitions.

7.1.3 User functions definition

Code+arrows – you can define which functions will be started on entering the code and

tapping the selected arrow key.

7.1.4 Macro commands

The macro commands related data are stored in the keypad memory. Before you start

defining the macro commands, click on the “Read” button in the “Macro commands”

tab to read the data from the keypad. Having defined the macro commands, click on

the “Write” button in the “Macro commands” tab to write the data to the keypad. The

macro command related data are not read / written when you click on the button

in the main menu of D

LOAD

X program.

In the keypad with factory default settings, there are two macro commands defined

which are assigned to the first group:

0# – quick full arming (the control panel will only execute the macro command after

you define the partitions which are to be armed in the event of quick full arming –

see Q

UICK

RM PARTITIONS

p. 7);

9# – exit delay clearing (the control panel will execute the macro command if reducing

the exit delay time is allowed by the partition settings and the E

XIT DELAY CLEARING

ENABLE

option is enabled in the keypad – see p. 9).

The “Reset” button in the D

LOAD

X program makes it possible to restore the keypad

factory settings, i.e. those related to macro commands, status screen and EOL

resistors (in the case of the keypads supported by the INTEGRA Plus control panels,

the EOL resistor values are not programmed individually for keypad zones).

Groups

The macro commands which are to be available for the keypad users must be assigned to

one of the four groups. Up to 16 macro commands can be assigned to a group. Up to 6

macro command icons can be displayed on the keypad screen at the same time. The

LOAD

X program presents groups of macro commands and macro commands assigned to

them in a tree form.

Name – name of the macro command group which is displayed on the keypad screen under

the icon (up to 16 characters in two lines, up to 8 characters in the line). Do not enter the

name if it is not to be displayed.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Satel INT-TSG-BSB Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Satel INT-TSG-BSB

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info