Bedienungsanleitung Satel Integra 128 Plus (Seite 59 von 102) (Englisch)

699072

Zoom out

Zoom in

Vorherige Seite

1/102

Nächste Seite

SATEL INTEGRA Plus 57

Reporting delay – option for the 4-8 and 64-79 zone types. Violation of the zone during the

entry delay countdown will trigger a warning alarm. The warning alarm does not cause any

loud alarm signal and is not reported. It can be signaled by the outputs of 9. DAY ALARM,

12. SILENT ALARM and 116. INTERNAL SIREN type. If the zone is not disarmed within 30

seconds, the entry delay has expired or another instant is violated, the burglary alarm will

be triggered.

Blocks verification – option for 0-2, 85-86 and 94-95 zone types. If it is enabled, violation of

the zone will block verification of alarms in the partition. All alarms will be unverified until

the partition is armed again.

Check arm possibility – option for the arming zones (80 and 82 zone types). The zone will

not arm, if a zone with enabled PRIORITY option is violated in the partition, or other

circumstance have occurred which prevent arming (depending on the selected options,

tamper, trouble, etc.).

Restore disarms – option for the 89. FINISHING EXIT DELAY zone type. If it is enabled, the

zone restore will disarm the partition. This option overrides the option RESTORE DISABLES

VERIF

Restore disables verif. – option for the 89. FINISHING EXIT DELAY zone type. If it is enabled,

the zone restore will disable verification of alarms in the partition. All alarms will be

unverified until the partition is armed again.

Disabled in arm state – option for the 91. DETECTOR MASK zone type. If the option is enabled

and the zone is violated when armed, the information on detector trouble (masking) will not

be stored into the event log (the event code will not be sent to the monitoring station).

4.3.7 Counters

The control panel makes it possible to program 16 different counters which determine the

operating mode of the counter zones (zone types 16-31). The counter parameters can be

programmed:

• using the keypad, in the service mode, by means of the COUNTERS function (ZONES

COUNTERS).

• using the DLOADX program, in the “Zones” window, “Counters” tab.

The following should be programmed for each counter:

Max. value – number of violations which, if exceeded, will trigger an alarm.

Counting time – the time in which violations are counted.

Counter type:

normal – all violations of counter group zones are counted,

omit recurs – skips violations of the same zone (the alarm will be triggered, if the number

of violations of different zones exceeds the maximum value).

If the counter skips repeats, the programmed MAXIMUM COUNTER VALUE must be lower

than the number of zones in counter group.

4.3.8 Bypasses

You can define a group of zones for each of the zone types from 64 to 79:

• using the keypad, in the service mode, by means of the BYPASSES function (ZONES

BYPASSES).

• using the DLOADX program, in the “Zones” window, “Bypasses” tab.

Having assigned the zones to a group, define what reaction should be to violation of the

bypassing zone:

Bypass only – the zones belonging to the group will be bypassed for BYPASS TIME (see:

p. 50).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Satel Integra 128 Plus Seite 59

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Satel Integra 128 Plus

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info