Bedienungsanleitung Satel Integra 128 Plus (Seite 60 von 102) (Englisch)

699072

Zoom out

Zoom in

Vorherige Seite

1/102

Nächste Seite

58 Programming SATEL

Bypass on/off – the zones belonging to the group will remain bypassed as long as the

bypassing zone is violated (they can be bypassed by the user).

In the LCD keypad, use the BYPASS ON/OFF option to make your selection. Option

disabled – see: BYPASS ONLY. Option enabled – see: BYPASS ON/OFF.

4.3.9 Groups of partitions

You can define up to 16 partition groups which will be controlled using the 80. ARMING,

81. DISARMING and 83. CLEARING ALARM type zones. The partition groups can be defined:

• using the keypad, in the service mode, by means of the GROUPS function (ZONES

GROUPS).

• using the DLOADX program, in the “Zones” window, “Arm/Disarm Groups” tab.

4.3.10 Zone testing

Using the function available in the service mode menu in the keypad (ZONES TEST), you

can test the zones. Information on violation or tamper of the zone is displayed and signaled

by beeps in keypad (violation – 5 short beeps; tamper – 1 long beep; masking – 3 long

beeps). Additionally, the function allows selection of a system output which will be used for

signaling during the test (zone violation will activate the output for 0.4 second, tamper – for

1,6 seconds, masking – for 3 seconds).

Violation/tamper/masking of the zone during the test will not trigger the response

programmed for the control panel zone.

Select a zone for testing from the list and press the or  key. The output allocated

for signaling will stop doing its present duty (if it was active, it will be disabled) until the

zone test is completed (the key pressed).

The output used for signaling is only remembered until exiting the TEST function. When

the TEST function is re-started, the output must be selected again.

If wireless sirens are used in the system and any output is selected for signaling, after

selecting a zone for testing from the list and pressing the or  key, in the wireless

sirens the signaling will be unblock (which is normally blocked for the service mode

duration).

If the output selected for signaling controls the wireless siren, it should be borne in

mind that the command to block/unblock signaling is sent out during polling. This

results in a delay whose duration depends on the programmed response period. Also

in case of the ASP-205 siren signaling is only triggered during the polling period.

5. Outputs

The system supports the following outputs:

• hardwired – on the control panel electronics board and in expanders. The number of

available hardwired outputs is determined by the control panel during identification

procedure.

• wireless – after connecting the ABAX 2 / ABAX wireless system controller. The number of

available wireless outputs depends on the number of wireless devices registered in the

system and is determined during the procedure of adding wireless devices.

• virtual – the outputs which do not exist physically, but can be used e.g. for execution of

logical functions.

Programming of the outputs is possible:

• using the keypad, in the service mode, by means of functions available in the OUTPUTS

submenu,

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Satel Integra 128 Plus Seite 60

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Satel Integra 128 Plus

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info