Bedienungsanleitung Satel Integra 128 Plus (Seite 90 von 102) (Englisch)

699072

Zoom out

Zoom in

Vorherige Seite

1/102

Nächste Seite

88 Programming SATEL

10.1.5 Event codes

For the pulse and Ademco Express formats, it is necessary to program codes which will be

reported to the monitoring station if the defined events occur. The reported events are those

for which a code different from “00” has been programmed. 2 hexadecimal characters (digits

or letters from A to F) are to be programmed.

In case of the CONTACT ID (SELECTED) and SIA (SELECTED) formats, indicate the events

which are to be reported, entering for them any code different from “00” (a code

consistent with the format specification will be sent, not the entered one). The events

for which the “00” code has been programmed will not be reported.

10.1.6 Test transmissions

The test transmission may be sent:

• at a specified time. The test transmission code will be sent regularly at a defined time. The

number of days between transmissions and the time of sending transmission are

programmed.

• in specified time intervals. For each monitoring station, the number of days, hours and

minutes between transmission can be individually programmed. The test transmission

code will be sent:

– after a predefined period of time has elapsed since the last transmission, irrespective of

whether it was a test transmission, or the code of another event was sent (the NO SYNC.

TO LAST TRANSMISSION

option disabled),

– at predefined time intervals (the NO SYNC. TO LAST TRANSMISSION option enabled).

10.2 Starting the reporting

10.2.1 Telephone reporting

1. Enable the REPORTING – TELEPHONE option.

2. Using the telephone options (see: “Telephone options” p. 68):

– determine how the telephone numbers should be dialed (TONE DIALING option and – in

case of the pulse dialing – PULSE DIALING 1/1,5 (OFF:1/2) option),

– determine whether the control panel, prior to dialing the number, should check the

telephone line for dialing signal (NO DIAL TONE TEST option).

3. Determine whether the event codes will be sent to both monitoring stations or to one of

them only (STATION 1 OR 2 / STATION 1 / STATION 2 / STATION 1 AND 2).

4. Program the following for the monitoring station to which event codes are to be sent:

– telephone number,

– reporting format in which the codes will be sent,

– the number of attempts to connect to the station after which, if there is no connection,

the control panel will suspend reporting (REPETITIONS),

– time for which reporting will be suspended after the programmed number of attempts to

establish connection with the station has been made (SUSPEND TIME),

– identifiers with which the events will be sent,

– events assignment (if STATION 1 AND 2 is selected),

– advanced options (if Ademco Express, Contact ID, SIA or TELIM format is selected).

5. If a reporting format other than CONTACT ID (FULL) or SIA (FULL) is selected:

– assign identifiers to the partitions, zones, keypads and expansion modules,

– program the codes for events which are to be reported.

6. Define the parameters of test transmissions.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Satel Integra 128 Plus Seite 90

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Satel Integra 128 Plus

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info