Bedienungsanleitung Satel Integra 128 (Seite 32 von 51) (Englisch)

699073

Zoom out

Zoom in

Vorherige Seite

1/51

Nächste Seite

30 User Manual SATEL

5.8.6 Adding keyfob

1. When adding or editing a user, run the NEW RX KEYFOB / NEW ABAX KEYFOB function

(depending on which keyfob is to be added).

2. Using the  and  keys, select how the keyfob is to be added. The number of keyfob

can be read during transmission by a device supporting keyfobs or entered manually.

3. Press the

key

4. If the keyfob number is to be read, press twice the keyfob button according to the

instructions displayed on the keypad. When the keyfob number is displayed, press the

key.

5. If the keyfob number is to be entered, enter it from the keypad, and then press the

key.

6. You will be brought back to the list of functions for defining the user parameters. Instead

of the NEW RX KEY FOB / NEW ABAX KEYFOB function, the REM. RX KEY FOB / REM.ABAX

KEYFOB

function will be available. Additionally, some functions appear to allow you to

configure the keyfob.

Prior to assigning the zones to buttons / combinations of buttons, consult the installer.

Numeration of the keyfob buttons and LEDs is described in section “Operating the

alarm system by means of keyfob” (p. 46).

7. Using the  key, find the BUTTON 1 function in the list, and then press the

key.

8. Using the  and  keys, select which zone is to be violated on pressing the 1 button in

the keyfob (you can also enter the zone number from the keypad), and then press the

key.

9. Repeat the steps 7 and 8 for other buttons / combinations of buttons which are to be

used.

10. Using the  key, find the EVENTS (RX) / EVENTS (ABAX) function in the list.

11. Press the

key. The list of buttons / combinations of buttons will be displayed. In the

upper right-hand corner of the display, an additional symbol is located:

– pressing the button / combination of buttons is written to the event log (default

setting),

– pressing the button / combination of buttons is not written to the event log.

12. Define whether pressing the button / combination of buttons will be written to the event log

(see: “Selection from the multiple-choice list” p. 16), and then press the

key.

13. For the APT-200 (ABAX 2 / ABAX) / APT-100 (ABAX) keyfobs, use the  key to find the

ABAX CONFIRMAT. function in the list, and then press the

key.

14. A list will be displayed showing the outputs which have been assigned by the installer for

confirmation (maximum 8). Select up to 3 of them (see: “Selection from the multiple-

choice list” p. 16). Upon pressing any keyfob button, information on the status of selected

outputs will be presented on the keyfob LEDs for a few seconds. Thus you can get

confirmation that the function has been executed or information on the current status of

the system.

The installer can define the list of outputs by means of the keypad (ABAX CONFIRMAT.

function [SERVICE MODE STRUCTURE HARDWARE EXPANDERS ABAX CONFIRMAT.]

or a computer with the DLOADX program (“Keyfobs ABAX” window).

15. Press the

key

16. Press the

key

17. When a prompt appears, asking you if the changes are to be saved, press the 1 key.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Satel Integra 128 Seite 32

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Satel Integra 128

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info