Bedienungsanleitung Satel Integra 24 (Seite 43 von 114) (Englisch)

699079

Zoom out

Zoom in

Vorherige Seite

1/114

Nächste Seite

SATEL INTEGRA 41

Required settings of the DLOADX program for direct communication with the module:

• programmed: number of TCP port used for communication and data encryption key

(DLOADX KEY).

1. Click on the button in the DLOADX program.

2. A drop-down menu will be displayed. Select “TCP/IP: DLOADX <- ETHM/INT-GSM” in it.

3. Send to the INT-GSM module the following SMS message:

xxxx= (“xxxx” – the control command to initiate establishment of communication with

DLOADX program) – the module is to connect to the computer address programmed in

the module,

xxxx=aaaa:p= (“xxxx” – the control command to initiate establishment of communication

with DLOADX program; “aaaa” – address of the computer with DLOADX program (IP

address or domain name); “p” – TCP port) – the module is to connect to the computer

whose address has been given in the SMS message and use for communication the

TCP port given in the SMS message.

4. The DLOADX program will inform you about establishing connection by means of

a suitable message.

Establishing connection via the SATEL server

For communication via the SATEL server, the ports of 1024-65535 range are used as

outgoing ports. These ports must not be blocked.

If the INT-GSM module is connected to the ETHM-1 Plus module and connection over

Ethernet cannot be established, an attempt will be made to establish connection via

GPRS.

Required settings of the ETHM-1 Plus module:

• CONNECTION VIA SATEL SERVER option enabled.

Required settings of the DLOAX program for communication via the SATEL server:

• programmed: identification number assigned to the ETHM-1 Plus module by the SATEL

server (ETHM-1 ID), MAC address of the ETHM-1 Plus module (ETHM-1 MAC) and data

encryption key (DLOADX KEY) or selected set of parameters “Module: ETHM-1, Address n”

(settings of the ETHM-1 Plus module with address “n” will be used).

1. Click on the button in the DLOADX program.

2. A drop-down menu will be displayed. Select “TCP/IP: Satel server”.

3. A window will open. Click on the “Connection” button in the window.

4. The DLOADX program will inform you about establishing connection by means of

a suitable message.

3.4.3 Starting remote GPRS programming

The GPRS programming is possible in the case of INTEGRA 128-WRL or any other control

panel, if the INT-GSM module is installed in the alarm system or the SATEL GSM module is

connected to the control panel.

Programming the INTEGRA 128-WRL control panel

GPRS connection to the INTEGRA 128-WRL control panel can be established in one of the

following methods:

1. Initiating connection from the keypad (by the control panel). The control panel can be

programmed only from specified location. This method is recommended when the alarm

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Satel Integra 24 Seite 43

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Satel Integra 24

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info