Bedienungsanleitung Satel Integra 24 (Seite 67 von 114) (Englisch)

699079

Zoom out

Zoom in

Vorherige Seite

1/114

Nächste Seite

SATEL INTEGRA 65

94. ALARM – UNAUTHORIZED ACCESS – similarly as type 93, but the signaling only applies to

modules with enabled ALARM ON UNAUTH. ACCESS option.

95. IP REPORTING TROUBLE – signals troubles related to reporting over Ethernet and by means

of GPRS.

96. TELEPHONE LINE TROUBLE – informs about telephone communication troubles.

In the case of INTEGRA 128-WRL control panel, the output type 96 is called GSM

TROUBLES and indicates the GSM communication related troubles.

97. VOICE MESSAGE – similarly as types 48-63, but the numbers of synthesizers (messages)

must be selected.

98. REMOTE SWITCH – similarly as types 64-79, but the numbers of remote switches must be

selected.

99. ACCESS CARD READ – signals read-in of the user card.

100. CARD HOLD – DOWN – signals holding the user card.

101. CARD READ – EXPANDER – signals that the card has been read in indicated

modules/keypads.

The 101. CARD READ – EXPANDER type output may be used for execution of the access

control function from INT-KLCDR / INT-KLFR / INT-KWRL2 / INT-KWRL keypad. To

do so:

− in the output settings, indicate the keypad on which reading in the card will activate

the output, and the partitions from which the users will be able to open the door,

− in the keypad settings, assign the door opening function to presenting / holding the

card and indicate the 101. CARD READ – EXPANDER type zone as the door to be

opened.

102. LINK TROUBLE – WIRELESS ZONE – signals lack of communication with wireless devices

assigned to the selected zones.

103. LINK TROUBLE – WIRELESS OUTPUT – signals lack of communication with wireless devices

assigned to the selected outputs.

104. WIRELESS DEVICE – LOW BATTERY – signals some problems with power supply of wireless

devices.

105. SHUTTER UP – dedicated for raising the roll shutters. It becomes active after violation of

selected zones or disarming of selected partitions. It can also be triggered from the

keypad, by means of the user function OUTS CONTROL. The cut-off time programmed for

the output should be longer than that required for raising the roll shutters.

106. SHUTTER DOWN – dedicated for lowering the roll shutters. It becomes active after

violation of selected zones or arming of selected partitions (upon starting the arming

procedure). It can also be triggered from the keypad, by means of the user function OUTS

CONTROL

. The cut-off time programmed for the output should be longer than that required

for lowering the roll shutters.

The roller shutter “up” and “down” functions must be assigned to consecutive

(following each other) physical outputs.

If the 105. SHUTTER UP and 106. SHUTTER DOWN type outputs are to be controlled from

the keypad, they must be assigned to a group of outputs (see: “Output groups” p. 68).

For the 105. SHUTTER UP and 106. SHUTTER DOWN type outputs, indicate a partition so

that these outputs can be controlled from the keypad serving the given partition. If the

partition status is not to control the output status, enable the NOT CONTROLLED BY

ARMING option.

107. CARD ON READER A – indicates the proximity card / DALLAS iButton read-in by the

expander reader A. It can also signal card reading in the LCD keypad.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Satel Integra 24 Seite 67

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Satel Integra 24

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info