Bedienungsanleitung Satel Integra 256 Plus (Seite 53 von 102) (Englisch)

699031

Zoom out

Zoom in

Vorherige Seite

1/102

Nächste Seite

SATEL INTEGRA Plus 51

4. 2EOL/NC – the zone supports a detector of NC type with two EOL resistors in the

circuit,

5. 2EOL/NO – the zone supports a detector of NO type with two EOL resistors in the

circuit,

6. Roller – the zone supports a roller shutter detector,

7. Vibration – the zone supports a vibration detector (also NC type detector),

8. Follow output – the zone does not support any detectors – its status depends solely on

the status of selected output (physical violations and tampers of the zone are ignored),

9. Roller 2EOL – the zone supports a roller shutter detector with two EOL resistors in the

circuit,

10. Vibration 2EOL – the zone supports a vibration detector (also NC type detector) with

two EOL resistors in the circuit,

11. 3EOL/NC – the zone supports a detector of NC type with three EOL resistors in the

circuit,

12. 3EOL/NO – the zone supports a detector of NO type with three EOL resistors in the

circuit.

Zone sensitivity – depending on wiring type:

NO, NC, EOL, 2EOL/NC, 2EOL/NO, 3EOL/NC and 3EOL/NO – the time during which the

zone must be violated, so that it can be noted by the control panel.

Roller / Roller 2EOL – 2 parameters are to be programmed (in the DLOADX program,

you should enter two numbers in the ZONE SENSITIVITY field):

Pulses duration – the time period during which a specified number of pulses must

occur (PULSES COUNT) for the zone to be violated. You can enter 0 (the pulse counter

will only be reset on arming / disarming), 1 (30 seconds), 2 (120 seconds) or 3 (240

seconds).

Pulses count – the number of pulses after which the zone will be violated. You can

program values from 1 to 8.

Vibration / Vibration 2EOL – 2 parameters are to be programmed (in the DLOADX

program, you should enter two numbers in the ZONE SENSITIVITY field):

Sensitivity – occurrence of a pulse whose duration is equal to or longer than the

defined time will cause violation of the zone. You can program values from the 3 ms

to 96 ms range (every 3 ms).

Pulses count – the number of pulses after which the zone will be violated. You can

program values from 0 to 7. If the value 0 is programmed, the pulses will not be

counted – only SENSITIVITY will be taken into account.

Output – refers to the FOLLOW OUTPUT wiring type. Indicate the number of output whose

activation will violate the zone. The output can be a virtual one.

Max. violation time / Max. door opening time – exceeding the maximum time of

violation/door opening is recognized by the control panel as a detector failure/door failure.

If the value 0 is programmed, control of this time is disabled.

Max. no violation time – exceeding the maximum time of no violation is recognized by the

control panel as a detector failure. The time will only be counted when the zone is

disarmed. If the value 0 is programmed, control of this time is disabled. The time can be

programmed in hours or minutes.

It is recommended that you program the MAX. NO VIOLATION TIME parameter, since it will

provide an additional supervision of the detector connected to the zone.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Satel Integra 256 Plus Seite 53

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Satel Integra 256 Plus

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info