699031
66
Zoom out
Zoom in
Vorherige Seite
1/102
Nächste Seite
64 Programming SATEL
109. ZONES LOGICAL ANDactive, when all zones selected as the control ones are violated.
110. ALARM NOT VERIFIEDsignals unverified alarms.
111. ALARM VERIFIEDsignals verified alarms.
112. VERIFIED NO ALARM informs that the alarm has not been verified (during the alarm
verification no alarm was triggered by any other zone included in the verification).
113. VERIFICATION DISABLED STATUSsignals disabling alarm verification.
114. ZONE TEST STATUS indicates the zone testing by means of user functions.
115. ARMING TYPE STATUSactive when selected partitions are armed in the selected mode.
116. INTERNAL SIREN signals the same alarms and violations as the 1. BURGLARY or 9. DAY
ALARM output type (logic product of the 1. BURGLARY and 9. DAY ALARM outputs).
117. TAMPERING STATUSinforms about tamper of selected zones, keypads and expanders.
118. KEYFOB BATTERY LOW informs about low battery in keyfobs belonging to selected
users. Refers to the 433 MHz keyfobs (supported by the INT-RX or INT-RX-S modules) or
the APT-200 (supported by the ABAX 2 / ABAX system) / APT-100 keyfobs (supported by
the ABAX system).
119. WIRELESS SYSTEM JAMMING indicates the jamming of device supporting the ABAX 2
(ACU-220 or ACU-280 controller) / ABAX wireless system (ACU-120, ACU-270, ACU-100
or ACU-250 controller).
120. THERMOSTAT the output activates when temperature drops below a preset value. The
control panel can receive the temperature data from wireless temperature detectors or
ABAX 2 wireless devices provided with a temperature sensor. For more information, refer
to section 120. Thermostat output parametersp. 66.
121. MASKING signals for a programmed time masking the detectors connected to the 3EOL
zones.
122. MASKING STATUS indicates the masking the detectors connected to the 3EOL zones.
5.3 Options
Pol.+ defines the output operating mode (see Table 5).
high-current output
option enabled
(normal polarity)
option disabled
(reversed polarity)
active status
+12V voltage supply
+12V voltage cut-off
inactive status
+12V voltage cut-off
+12V voltage supply
low-current output
option enabled
(normal polarity)
option disabled
(reversed polarity)
active status
shorted to ground
isolated from ground
inactive status
isolated from ground
shorted to ground
Table 5. Functioning of outputs, depending on the POL.+ option.
Pulsatingthe option refers to timed outputs. If it is enabled, the output operates in
a pulsating mode. If it is disabled, the output operates continuously.
Latch the option refers to alarm outputs. If it is enabled, the output will be active until the
alarm is cleared by the user.
Active during violation the option applies to the 24. MONO SWITCH output. If enabled, the
output is always active when a control zone is violated, and the countdown of output cut-
off time will only be running after the violation ends.
66

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Satel Integra 256 Plus wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Satel Integra 256 Plus

Satel Integra 256 Plus Bedienungsanleitung - Deutsch - 55 seiten

Satel Integra 256 Plus Zusatzinformation - Deutsch - 108 seiten

Satel Integra 256 Plus Installationsanweisung - Deutsch - 36 seiten

Satel Integra 256 Plus Bedienungsanleitung - Englisch - 51 seiten

Satel Integra 256 Plus Installationsanweisung - Englisch - 35 seiten

Satel Integra 256 Plus Kurzanleitung - Holländisch - 2 seiten

Satel Integra 256 Plus Zusatzinformation - Holländisch - 108 seiten

Satel Integra 256 Plus Bedienungsanleitung - Holländisch - 53 seiten

Satel Integra 256 Plus Installationsanweisung - Holländisch - 35 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info