Bedienungsanleitung Satel Integra 256 Plus (Seite 68 von 102) (Englisch)

699031

Zoom out

Zoom in

Vorherige Seite

1/102

Nächste Seite

66 Programming SATEL

Partitions – for the 11. CHIME type output, you can indicate the partitions from which the user

will be able to block the output using the OUTPUTS CHIME function.

5.7 120. Thermostat output parameters

Temperature detector – indicate the zones to which the wireless temperature detectors or

ABAX 2 wireless devices provided with a temperature sensor are assigned.

Temperature T1 – the first temperature threshold. It is active when all control timers are OFF

or the forcing output is active. If the temperature threshold is active, the output will be

turned on if the temperature drops below the threshold.

Temperature T2 – the second temperature threshold. It is active when the control timer is

ON or the forcing output is inactive. If the temperature threshold is active, the output will be

turned on if the temperature drops below the threshold.

Hysteresis – temperature difference between turning the output on and off. The output will

be turned on when temperature drops below the threshold by a value higher than the

hysteresis. The output will be turned off when temperature rises above the threshold.

Hysteresis is used to eliminate the undesirable output state changes when temperature

fluctuations occur. Programming “0” means that hysteresis is equal to 0.5°C.

The user can edit the temperature thresholds and hysteresis using the TEMPERATURES

user function available in the CHANGE OPTIONS submenu.

Output forcing T1 – you can indicate the output which will force the first temperature

threshold. If the output is active, the first temperature threshold will be active. When the

output is inactive, the control timers will decide which temperature threshold is active.

The output 256 cannot be indicated as the forcing one.

Timers controlling T1/T2 – you can indicate the timers which will control the temperature

threshold. When the control timer is ON, the second temperature threshold will be active

(unless the forcing output is active).

The user can edit the parameters of control timers using the TIMERS user function

available in the CHANGE OPTIONS submenu.

5.8 Output groups

The outputs of MONO SWITCH, BI SWITCH, REMOTE SWITCH, SHUTTER UP and SHUTTER DOWN

type can be grouped by the function performed by them. Each group may be given a name.

The output groups can be defined:

• using the keypad, in the service mode, by means of the OUTPUT GROUPS function,

• using the DLOADX program, in the “Output groups” window (to open the window, press

the “Output groups” button in the “Outputs” window).

If all outputs are assigned to one group of outputs, the keypad will not display the list

of output groups upon starting the REMOTE CONTROL user function, but it will

immediately display the list of outputs which can be controlled.

The output can be assigned to a few groups.

If the output is not assigned to any group, it cannot be controlled from the keypad.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Satel Integra 256 Plus Seite 68

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Satel Integra 256 Plus

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info