Bedienungsanleitung Satel Integra 256 Plus (Seite 70 von 102) (Englisch)

699031

Zoom out

Zoom in

Vorherige Seite

1/102

Nächste Seite

68 Programming SATEL

displayed. Select the output to be tested and press the

or  key. The keypad will display

a submenu which enables the output testing. By using the or  key, you can

activate/deactivate the output. You can also deactivate the output by means of the numerical

keys. Press to quit the submenu and return to the list of system outputs.

The output under test will stop performing its previous function (if it was active, it will

be deactivated).

If there are wireless sirens in the system, starting the function of output testing will

unblock the signaling in them (the signaling is normally blocked for the service mode

duration). It should be remembered that the command to block/unblock the signaling is

sent out during polling. This will cause a delay whose duration depends on the

programmed response period.

When testing the control output for ASP-205 wireless siren, it should be remembered

that the signaling is only triggered during the polling.

6. System options

Most of the options and parameters described in this section can be programmed:

• using the keypad, in the service mode, by means of the functions available in the OPTIONS

submenu,

• using the DLOADX program, in the “Options” window.

Shown in square brackets are the names used in keypads.

6.1 Telephone options

Reporting - TELEPHONE [Mon.TELEPHONE] – with this option enabled, the control panel

can send event codes by means of the telephone line.

Reporting - GPRS [Mon.GPRS] – if this option is enabled, the control panel can send event

codes via GPRS by using the SATEL GSM module.

The REPORTING – GPRS option does not apply to GPRS reporting via the INT-GSM

module.

Reporting - ETHM [Mon.ETHM-1] – the option is available if the ETHM-1 Plus / ETHM-1

module is connected to the control panel, but the INT-GSM module is not included in the

alarm system. If this option is enabled, the control panel can send event codes over

Ethernet by using the ETHM-1 Plus / ETHM-1 module.

Reporting – ETHM/INT-GSM [Mon.ETHM-1] – the option is available if the INT-GSM module

is installed in the alarm system. If this option is enabled, the control panel can send event

codes via Ethernet by using the ETHM-1 Plus / ETHM-1 module and/or via GPRS and

SMS by using the INT-GSM module.

Telephone messaging [Messaging] – if this option is enabled, the control panel can send

notifications via the telephone network of the occurrence of specific events using voice or

text messages defined by the installer.

SMS messaging – if this option is enabled, the control panel can send event notifications by

using SMS messages whose content is created automatically, based on the control panel

event log. The SATEL GSM module must be connected to the control panel.

If the INT-GSM module is installed in the alarm system, the SMS MESSAGING option is

not available. The SMS MESSAGING option does not apply to SMS messaging by the

INT-GSM module.

E-mail messaging [E-MAIL messag.] – if this option is enabled, the control panel can send

event notifications by e-mail messages, the content of which is created automatically,

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Satel Integra 256 Plus Seite 70

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Satel Integra 256 Plus

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info