Bedienungsanleitung Satel Integra 256 Plus (Seite 72 von 102) (Englisch)

699031

Zoom out

Zoom in

Vorherige Seite

1/102

Nächste Seite

70 Programming SATEL

6.2 Printer options

Printing – the option enables on-line events printout by the printer connected to the RS-232

port of control panel mainboard.

6.2.1 Printout options

Include reporting status [Monitor.status] – on the printout will appear the information if the

particular event was sent to the monitoring station (printout of the event information will

take place not immediately but after transmission to the station has been completed).

Print names/descriptions [Names/descript] – determines if, besides the numbers of zones,

outputs, modules and users, also their names and descriptions are to be printed.

Wide paper – printout width will be 132 columns (if the option is disabled: 80 columns).

2400 bps (off:1200 bps) – data will be sent to RS-232 port at a rate of 2400 bps (if the

option is disabled - at a rate of 1200 bps).

CR+LF (off: CR) – parameter determining the control mode of paper feed in the printer.

Use parity bit – the parity check of data transferred from the control panel to the printer is

enabled.

Parity EVEN (off: ODD) – option determines the mode of parity check of data transferred

from the control panel to the printer. The option is relevant only if the USE PARITY BIT option

is active.

The other parameters of RS-232 transmission are permanently programmed (8 data

bits, 1 stop bit).

All the parameters regarding transmission through RS-232 (i.e. transmission rate,

CR+LF, parity, data bits and stop bits) are to be set identically on the control panel and

on the connected printer. Otherwise the printer will not operate at all, or the printout

will be illegible.

6.2.2 Printout contents

The options define what kind of information will be contained in the printout.

6.3 Other options

Permitted “simple” access codes [Simple codes] – with this option enabled, with this

option enabled, it is possible to use codes containing less than three different digits (e.g.

1111 or 1212) or consisting of consecutive digits (e.g. 3456).

Notify of necessity to change access code [Notify of code] – with this option enabled, the

keypad will notify the user of the necessity to change access code, if it is known to other

users.

Confirm commands with “1” [Confirm with 1] – if this option is enabled, the LCD keypad

will require, in case of some functions, additional confirmation with the key 1.

Clear messaging on alarm clearing [Autoabort msg.] – with this option enabled, clearing

the alarm can automatically cancel messaging about this alarm, if the user clearing the

alarm has the TELEPHONE MESSAGING CANCELING right.

Return to menu from Service Mode [SM -> menu] – if this option is enabled, exiting the

service mode will be followed by return to the user menu instead of to the basic operating

mode of the keypad.

Return to menu from menu “Test” [Tests -> menu] – if this option is enabled, exiting the

user function available in the TESTS or CHANGE OPTIONS submenu will be followed by return

to the submenu instead of to the basic operating mode of the keypad.

Fast module bus communication [Fast exp. bus] – it is recommended to enable this option

to speed up communication with the modules. The option should only be disabled in case

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Satel Integra 256 Plus Seite 72

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Satel Integra 256 Plus

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info