699074
24
Zoom out
Zoom in
Vorherige Seite
1/35
Nächste Seite
22 Installer Manual SATEL
5.10.2 Backup power supply
A 12 V lead-acid sealed battery should be connected to the control panel as a backup power
source. The battery capacity must be adequately selected to match current consumption in
the system. According to EN 50131 Grade 3, the battery must ensure operation of the system
without mains supply for 30 hours, when the reporting is enabled in the control panel.
Do not connect deeply discharged battery to the control panel (with voltage
across unloaded terminals below 11 V). The battery should be precharged with
a proper charger.
The used batteries must not be discarded, but should be disposed of in
accordance with the existing rules for environment protection.
If the battery voltage drops below 11 V for longer than 12 minutes (3 battery tests), the
control panel will indicate battery failure. When the voltage goes down to approx. 10.5 V, the
battery will be disconnected.
5.10.3 Control panel power-up / start-up procedure
1. Deenergize the 230 V AC circuit to which the transformer is to be connected.
2. Connect the 230 V AC wires to the terminals of transformer primary winding.
3. Connect the terminals of transformer secondary winding to the AC terminals on control
panel electronics board.
4. Connect the battery to the dedicated leads (positive terminal to RED lead, negative
terminal to BLACK lead). The control panel will not start after connecting the battery
alone. Included in the control panel set are adapters (matching connectors) for
connection of battery with twisted cable ends, therefore the battery cable ends should not
be cut off.
5. Turn on 230 V AC power supply in the circuit to which the transformer is connected.
The control panel will start operating.
If you have any problems with starting the control panel, enter the service mode
from the pins and restore the factory default settings (see EMERGENCY
PROCEDURE OF THE CONTROL PANEL START-UP p. 23).
The above mentioned power-up sequence (first the battery, then the 230 V AC mains) will
ensure proper operation of the power supply unit and the electronic protection circuits, thus
preventing damage to the alarm system components caused by installation mistakes, if any.
If the control panel power supply has to be disconnected, disconnect the mains first
and then the battery. When reconnecting the power supply, observe the above
mentioned sequence.
5.11 First start-up of the control panel
After the first start-up of the control panel, it is advisable to restore the factory
default settings using the CLEAR ALL function ([SERVICE CODE] SERVICE MODE
RESTARTS CLEAR ALL), and then quit the service mode. When a prompt
appears on the keypad display, whether the data should be saved to the FLASH
memory, press the “1” key on the keypad.
The control panel with factory settings (a new one or one after restart of settings) supports all
keypads connected to the bus, irrespective of the addresses set in them. However, it does
not allow you to program the system. You will be able to start programming after carrying out
the following operations:
1. Setting individual, correct addresses in keypads (see p. 14).
24

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Satel Integra 64 Plus wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Satel Integra 64 Plus

Satel Integra 64 Plus Bedienungsanleitung - Deutsch - 55 seiten

Satel Integra 64 Plus Zusatzinformation - Deutsch - 108 seiten

Satel Integra 64 Plus Installationsanweisung - Deutsch - 36 seiten

Satel Integra 64 Plus Bedienungsanleitung - Englisch - 51 seiten

Satel Integra 64 Plus Zusatzinformation - Englisch - 102 seiten

Satel Integra 64 Plus Bedienungsanleitung - Holländisch - 53 seiten

Satel Integra 64 Plus Zusatzinformation - Holländisch - 108 seiten

Satel Integra 64 Plus Installationsanweisung - Holländisch - 35 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info