Bedienungsanleitung Satel Integra 64 Plus (Seite 25 von 35) (Englisch)

699074

Zoom out

Zoom in

Vorherige Seite

1/35

Nächste Seite

SATEL INTEGRA Plus 23

2. Identification by the control panel of devices connected to the keypad bus. The

identification can be performed by means of:

– the keypad ([SERVICE CODE] SERVICE MODE STRUCTURE HARDWARE

IDENTIFICATION LCD KEYPADS ID.),

– DLOADX program (“Structure” window “Hardware” tab “Keypads” branch

“Keypads identification” button).

3. Identification by the control panel of devices connected to the expander bus. The

identification can be performed by means of:

– the keypad ([SERVICE CODE] SERVICE MODE STRUCTURE HARDWARE

IDENTIFICATION EXPANDERS ID.),

– DLOADX program (“Structure” window “Hardware” tab “Expansion modules” branch

“Exp. modules identification” button).

The identification function must be run every time when a new device is connected to

the bus or the address of a device connected to the bus is changed.

Disconnecting the identified device from the communication bus will trigger a tamper

alarm.

Any attempt to replace the identified device with another one having the same address

will trigger a tamper alarm.

5.12 Emergency procedure of the control panel start-up

If the control panel fails to start properly, keypads are not supported, codes are not accepted

by the control panel etc., despite all connections having been made correctly, follow the steps

below:

1. Turn off the control panel power supply (first disconnect the AC power, and then the

battery).

2. Put a jumper on the RESET pins located on the control panel mainboard.

3. Turn on the control panel power supply (first connect the battery and then the AC power).

The DIALER LED will start blinking.

4. Wait a few seconds until the DIALER LED goes out and remove the jumper from the pins.

The control panel will enter the service mode. The service mode menu will be displayed

on the keypad with the lowest address.

If a computer with the DLOADX program running is connected to the RS-232 port, the

service mode will not start (it will be possible to program the control panel locally from

the computer).

5. Restore the factory default settings using the CLEAR ALL function (RESTARTS CLEAR

ALL

6. Start the KEYPADS ADDR. function (STRUCTURE HARDWARE IDENTIFICATION KEYPADS

ADDR

.) and set individual addresses in the keypads (see p. 15).

7. Identify devices connected to the keypad bus (STRUCTURE HARDWARE

IDENTIFICATION LCD KEYPADS ID.).

8. Identify devices connected to the expander bus (STRUCTURE HARDWARE

IDENTIFICATION EXPANDERS ID.).

9. Exit the service mode using the END SERVICE function.

10. After a prompt appears on the keypad display whether to save the data to the FLASH

memory, press the key with the number 1. By saving a copy of the settings to the FLASH

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Satel Integra 64 Plus Seite 25

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Satel Integra 64 Plus

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info