Bedienungsanleitung Satel Integra 64 (Seite 86 von 114) (Englisch)

699075

Zoom out

Zoom in

Vorherige Seite

1/114

Nächste Seite

84 Programming SATEL

Event after 3 readings [Ev.3 unk.cards] – if this option is enabled, reading in an unknown

card three times will save the event.

Alarm after 3 readings [Al.3 unk.cards] – if this option is enabled, reading in an unknown

card three times will trigger an alarm. The option is available, if the EVENT AFTER 3

READINGS

option is enabled.

Code+card

Code OR card – the user can use code or card for authentication.

Code AND card – the user must use code and card for authentication.

Follow output – the authentication method depends on the status of selected output (the

output active – code and card; the output inactive – code or card).

In case of the authentication using code and card, the executed function depends on

the second identifier.

9. ABAX system – INTEGRA 128-WRL control panel mainboard

The parameters and options of the ABAX system and wireless devices supported by

INTEGRA 128-WRL control panel mainboard can be programmed:

• using the keypad, in the service mode, by means of the functions available in the ABAX -

INTEGRA submenu (STRUCTURE HARDWARE EXPANDERS SETTINGS ABAX -

INTEGRA),

• using the DLOADX program, in the “Structure” window, “Hardware” tab, after clicking on

the “Wireless System”.

The procedures of adding / deleting the ABAX 2 / ABAX wireless devices are described in the

INTEGRA 128-WRL installer manual.

The procedures of adding / deleting and configuring the ABAX 2 / ABAX keyfobs are

described in the user manual. You can define the list of outputs whose status is to be

presented by the ABAX 2 / ABAX keyfob LEDs:

• using the keypad, in the service mode, by means of the ABAX CONFIRMAT. function

(STRUCTURE HARDWARE EXPANDERS ABAX CONFIRMAT.),

• using the DLOADX program, in the “Keyfobs ABAX” window (the command for opening

this window is available in the “Users” menu).

When connecting the ABAX 2 / ABAX controller to the INTEGRA 128-WRL control

panel, you should synchronize the data related to APT-200 / APT-100 keyfobs. In the

keypad, in the service mode, the COPY ABAX KFOBS function is available (STRUCTURE

HARDWARE EXPANDERS COPY ABAX KFOBS), which enables copying the keyfob

related data. In the DLOADX program, to write to a new controller the data about

APT-200 / APT-100 keyfobs already assigned to the users, click on the “Write to all”

button in the “Keyfobs ABAX” window.

9.1 Parameters and options of ABAX system

Assigned to partition – partition in which an alarm will be triggered if the ABAX system is

jammed.

Response period – communication with wireless devices takes place in specified intervals.

The control panel is then gathering information on the status of wireless devices and, if

necessary, sending commands to the devices, e.g. switching the detectors to their

active/passive state, switching on/off the test mode and/or changing configuration of the

devices. The response period can be 12, 24 or 36 seconds. The less often communication

between the control panel and the wireless devices takes place, the more wireless devices

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Satel Integra 64 Seite 86

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Satel Integra 64

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info