Bedienungsanleitung Satel Integra 64 (Seite 87 von 114) (Englisch)

699075

Zoom out

Zoom in

Vorherige Seite

1/114

Nächste Seite

SATEL INTEGRA 85

can work within each other's operating range (12 seconds – up to 150, 24 seconds – up to

300, 36 seconds – up to 450). Beyond the response period, information about tampers of

devices and violations of detectors operating in active mode are sent to the control panel.

The response period has an effect on the level of energy consumption by the wireless

devices. The less often communication between the control panel and the wireless devices

takes place, the lower energy consumption and the longer battery life are.

In the case of the AMD-103 detector, no communication takes place during polling.

Higher sensitivity for jamming detection – if this option is enabled, the sensitivity of

detection of radio communication jamming is boosted.

Synchronize – this function starts the procedure of synchronization, i.e. checking for

presence of other ABAX 2 / ABAX wireless systems working within the control panel

operating range. The control panel will synchronize the response period so that the radio

transmissions of some systems should not be mutually jammed. Synchronization is

performed automatically upon starting the control panel and after each operation of

adding/removing devices supported by it.

Test mode – to carry out diagnostics / service work, you can start the test mode in the ABAX

system. When the system is running in the test mode:

– detector LEDs are enabled,

– tamper signaling in the sirens is blocked.

The command to start/end the test mode is sent during polling, i.e. with delay whose

duration depends on the frequency of polling. The test mode will be disabled automatically

30 minutes after:

– starting the test mode from the DLOADX program (the 30-minute period is running from

the moment of exiting the system ABAX settings),

– exiting the service mode in the control panel.

According to requirements of the EN50131 standard, the level of radio signals sent by

wireless devices is reduced during the test mode operation.

For the AMD-103 detector, entering the test mode remotely is not possible.

9.2 Parameters and options of wireless devices

Filter – the number of consecutive response periods, during which communication with the

device failed to be established, for the loss of communication with the device to be

reported. Values from the 0 to 50 range can be entered. Entering the digit 0 will disable

control of the device presence in the system.

In the case of the AMD-103 magnetic contact, the presence check is performed in

a different way than for the other ABAX 2 / ABAX devices. If the value programmed for

the FILTER parameter differs from 0, the lack of presence will be reported if no

transmission from the AMD-103 magnetic contact is received within one hour.

Always active – the option is available for the most of wireless detectors. If enabled, the

detector is permanently switched over to the active mode (see “Wireless detectors” p. 90).

The AMD-103 detector and the wireless detectors assigned to 24-h zones are always

in the active mode, therefore the ALWAYS ACTIVE option does not have to be enabled

for them.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Satel Integra 64 Seite 87

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Satel Integra 64

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info