Bedienungsanleitung Satel Integra 64 (Seite 92 von 114) (Englisch)

699075

Zoom out

Zoom in

Vorherige Seite

1/114

Nächste Seite

90 Programming SATEL

ASW-210

For each position occupied by the controller, enter 0 (relay can only be controlled via the

control panel), 1 (the input enables relay to be controlled with monostable switch) or 2 (the

input enables relay to be controlled with bistable switch).

9.2.2 Configuring the wireless devices – LCD keypad

Having started the CONFIGURATION function (STRUCTURE HARDWARE EXPANDERS

SETTINGS ABAX - INTEGRA. CONFIGURATION), use the  and  keys to select the zone

to which the do wireless device is assigned and press the

key. Use the arrow keys for

programming. The values which can be programmed for individual parameters of wireless

devices are presented in the section describing configuration of the devices by means of the

DLOADX program.

9.3 Specific character of the operation of wireless devices

This chapter describes the peculiar character of the operation of individual groups of wireless

devices, which affects the method of programming the zones and outputs to which the

wireless devices are assigned.

9.3.1 Wireless detectors

The zone to which a wireless detector is assigned is activated when the detector reports

alarm (select the appropriate zone type). If a detector tamper is to trigger the tamper alarm,

program the zone as 2EOL/NC or 2EOL/NO.

The mode of operation of wireless detectors depends on the status of partition to which the

zone with wireless detector belongs:

partition disarmed – the detector operates in passive mode. This operating mode prolongs

the battery life. Detector informs the control panel about its status during polling (only the

tamper information is sent immediately).

partition armed – the detector operates in active mode. The detector sends immediately all

information to the control panel.

Because switching the detectors over from the passive into active mode and conversely

takes place during the response time, it is performed with some delay in relation to

arming/disarming. The maximum delay – depending on the selected response frequency –

can be 12, 24 or 36 seconds.

The wireless detectors assigned to the 24-hour zones, which are permanently armed, are in

the active mode at all times. Also other wireless detectors can always work in the active

mode, if the ALWAYS ACTIVE option is enabled for them (see p. 85).

According to the EN50131-3 standard all ABAX 2 / ABAX Hold-Up devices must be

always in active mode.

The battery life time in the detectors switched permanently into the active mode is

shorter than in those which are periodically switched to the passive mode. However, if

the specific character of a detector or its installation place is such that the number of

alarms is low, switching the detector permanently into the active mode will not have

a significant effect on the battery life.

9.3.2 Wireless sirens

Turning on the output to which the wireless siren is assigned will trigger the signaling.

Depending on the siren:

ASP-105 – the first output controls acoustic signaling, and the other one – optical signaling.

The command to start or stop the signaling is sent to the siren immediately. The acoustic

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Satel Integra 64 Seite 92

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Satel Integra 64

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info