Bedienungsanleitung Satel Integra 64 (Seite 93 von 114) (Englisch)

699075

Zoom out

Zoom in

Vorherige Seite

1/114

Nächste Seite

SATEL INTEGRA 91

signaling stops after the maximum duration of acoustic signaling elapses, even if the

control output is still active. The optical signaling is active as long as the output is active.

ASP-205 / ASP-215 – both outputs control acoustic and optical signaling. Thus two different,

independently triggered ways of signaling can be configured. As a result, the outputs can

separately control the optical and acoustic signaling or trigger other signaling for different

alarms (e.g. burglary and fire). The command to start the signaling is sent to the siren only

during the response time. Therefore, the cut-off time for the control panel outputs which

control the siren must be longer than the response period. It is recommended that cut-off

time correspond to maximum duration of signaling programmed for the siren. The signaling

stops after the maximum duration of signaling elapses, even if the control output is still

active.

The zones to which the wireless siren is assigned are activated if a siren power supply

trouble occurs (select the appropriate reaction type for the zones):

ASP-105 – first zone: low battery; second zone: 12 V DC power loss.

ASP-205 / ASP-215 – both zones: low battery.

If the siren tamper is to trigger tamper alarm, program the zone as 2EOL/NC or 2EOL/NO.

The tamper information is sent immediately, while the trouble information – during the

response time.

Tamper alarm on opening the tamper switch in the siren:

ASP-105 – lasts for the maximum time of acoustic signaling programmed for the siren (sound

type selected during programming and optical signaling),

ASP-205 / ASP-215 – lasts 3 minutes (sound type 1 and optical signaling).

After starting the SERVICE MODE or TEST MODE and for 40 seconds after power-up, the

signaling in the siren is blocked. It enables installation work to be carried out. Opening

the tamper switch will not trigger loud signaling, but information on tamper will be sent

(when in service mode, the control panel will not signal the tamper alarms). The

command to block/unblock the signaling connected with starting / ending the test

mode or the service mode is sent during the response time.

9.3.3 Wireless expanders of hardwired zones and outputs

The wireless expander of hardwired zones and outputs (ACX-200 / ACX-201 / ACX-210 /

ACX-220) takes up 4 zones and 4 outputs in the system. You can configure the alarm system

zone/output to which expander zone/output is assigned in much the same way as hardwired

zones/outputs. You should remember however that sensitivity of the expander zones may be

different from that programmed in the control panel:

– from 20 ms to 140 ms – the same as the value programmed in the control panel,

– above 140 ms – only some values are available: 400 ms, 500 ms, 700 ms, etc. every

200 ms (the programmed value is rounded up to that supported by the expander).

The EN50131-3 standard requires that zones must react to signals lasting more than

400 ms. Therefore, select 400 ms when programming sensitivity of the alarm zones.

Information on the state of zones and commands to change the state of outputs are sent

immediately. Zone settings are sent during the response time (in one period, data relating to

configuration of one zone are sent to the expander module, i.e. sending the information on

settings of four zones require four response periods).

If communication with the control panel is lost, all previously activated outputs will be

deactivated after 20 response periods.

Additionally, the ACX-201 expander module sends information about:

• status of AUX1 and AUX2 power supply outputs – information on overload is sent when

the AUX1 or AUX2 output load exceeds 0.5 A.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Satel Integra 64 Seite 93

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Satel Integra 64

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info