Bedienungsanleitung Satel Integra 64 (Seite 95 von 114) (Englisch)

699075

Zoom out

Zoom in

Vorherige Seite

1/114

Nächste Seite

SATEL INTEGRA 93

– the timer start/end time when an exception applies.

If a year is programmed for an exception, the setting will only be valid for the current

year. If no year is programmed (the 9999 sequence is entered in the keypad instead of

the year), the exception will be valid every year.

Arming mode – the arming mode which will be activated when the timer starts (in the

DLOADX program, enter an additional digit next to the timer start time: 0 – full arming; 1 –

full arming + bypasses; 2 – arming without interior; 3 – arming without interior and without

entry delay).

11. User schedules

User schedules should be defined for the needs of the SCHEDULE type users (see: USER

MANUAL

). You can program the user schedules:

• using the keypad, in the service mode, by means of the functions available in the USER

SCHEDULES

submenu,

• using the DLOADX program, in the “Timers” window, “User Schedules” tab.

For each user schedule, you can:

• program an individual name (up to 16 characters),

• indicate the timers which will determine when the user will have access to the system.

12. Reporting

The control panel can send event codes to the monitoring station using the following

transmission paths:

• analog telephone line (INTEGRA 128, INTEGRA 64, INTEGRA 32 or INTEGRA 24 control

panel),

• GSM voice channel (INTEGRA 128-WRL control panel) – the use of this transmission path

is not recommended because of distortions that may occur when sending the event codes,

• Ethernet (connection of the ETHM-1 Plus / ETHM-1 module to the control panel required),

• GPRS (INTEGRA 128-WRL control panel; in case of other control panel INT-GSM module

must be installed in the alarm system or SATEL GSM module must be connected to the

control panel),

• SMS (INTEGRA 128-WRL control panel; in case of other control panel INT-GSM module

is required to be installed in the alarm system) – the control panel gets no

acknowledgement of event code receipt.

The control panel will try to send event code to the monitoring station using in turn:

1. ETHM-1 Plus / ETHM-1 module and/or INT-GSM module. If several such modules are

connected to the control panel, that with the lowest address will be used. Event code can

be sent via Ethernet, GPRS or SMS.

When configuring the ETHM-1 Plus module to which the INT-GSM module is

connected, or when configuring the INT-GSM module connected directly to the control

panel, define priority of the transmission paths. The transmission path which is not

included in the list defining the priority of transmission paths, will not be used.

2. GSM phone [INTEGRA 128-WRL control panel] / SATEL GSM module [any control panel]

for GPRS transmission.

3. GSM phone to send SMS [INTEGRA 128-WRL control panel],

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Satel Integra 64 Seite 95

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Satel Integra 64

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info