Bedienungsanleitung Satel Integra 64 (Seite 96 von 114) (Englisch)

699075

Zoom out

Zoom in

Vorherige Seite

1/114

Nächste Seite

94 Programming SATEL

4. analog telephone line [INTEGRA 128, INTEGRA 64, INTEGRA 32 or INTEGRA 24 control

panel] / GSM voice channel [INTEGRA 128-WRL control panel] (basic and backup

telephone number).

If the event code is successfully sent via one transmission path, the other transmission paths

will not be used.

If sending the event code via one transmission path fails, the control panel will try to send the

event code by using the next transmission path. In the case of reporting via the telephone

line, if the event cannot be sent despite completion of the preprogrammed number of retries,

the control panel will hang up until a next event occurs, or for a specified period of time. After

the time expires, the control panel will make further attempts to send the event.

The reporting parameters can be programmed:

• using the keypad, in the service mode, by means of the functions available in the

MONITORING submenu,

• using the DLOADX program, in the “Reporting” window.

For correct operation, the reporting function may require enabling some system options.

Reporting through the ETHM-1 Plus / ETHM-1 / INT-GSM / GSM modules requires that some

telephone options be enabled and settings of these modules properly configured.

Before you proceed to the programming, obtain from the monitoring station operator all data

necessary to correctly start the reporting function:

• depending on the method of sending events:

– telephone number of the monitoring station (telephone reporting),

– server address, port number, STATION KEY and KEY (ETHM) (reporting through Ethernet

network),

– server address, port number, STATION KEY and KEY (GPRS) (GPRS reporting),

– telephone number of the monitoring station and SMS message format (SMS reporting),

• transmission format required by the monitoring station,

• identifiers assigned to the alarm system,

• list of event codes (not applicable to Contact ID and SIA formats).

12.1 Reporting parameters and options

See also section “Telephone options” p. 69.

Shown in square brackets are the names used in keypads.

12.1.1 Options

Station 1 or Station 2 – the control panel will make an attempt to send the event code to

station 1 and, if unsuccessful, to station 2.

Station 1 only – the event codes are only sent to station 1.

Station 2 only – the event codes are only sent to station 2.

Station 1 and 2 – the event codes are sent to both stations. For most formats, it is possible

then to define which events will be sent to the given station (see: EVENTS ASSIGNMENT).

Dual path reporting – the option is available when the ETHM-1 Plus module with the

INT-GSM module attached to it is connected to the control panel. The control panel will

make an attempt to send the event code to station 1 and, if unsuccessful, to station 2.

The dual path reporting requires that the following settings be additionally

programmed:

− just one transmission path for Station 1: ETHM (Ethernet) [settings of the ETHM-1

Plus module with the INT-GSM module connected to it],

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Satel Integra 64 Seite 96

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Satel Integra 64

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info