Bedienungsanleitung Satel Integra 64 (Seite 36 von 51) (Englisch)

699075

Zoom out

Zoom in

Vorherige Seite

1/51

Nächste Seite

34 User Manual SATEL

– additional information on the events in shortened form, e.g. number of partition, zone,

user, timer, expander, keypad, etc.

Event description is displayed in the lower line.

If no key is pressed for a few seconds, additional information on the event will be displayed,

e.g. name of partition, zone, user, timer, expander, keypad, etc. After a few seconds, the

event description will be displayed again, and so on.

Pressing the  key enables the manual toggling between description of the event and

additional information on the event.

Pressing the  key when the event description is displayed will allow you to see further

additional information on the event, shown in a shortened form.

Using the  or  key will block the automatic toggling between description of the event and

additional information on the event.

After the list of events has been scrolled through with the use of the  or  key, the

automatic toggling between description of the event and additional information on the event

will be restored.

5.12 Replacing batteries in wireless keypad

If the battery in the INT-KWRL2 / INT-KWRL wireless keypad is low, it should be replaced.

You must run the REPLACE BATTERY function before you open the keypad enclosure.

1. Enter the code and confirm with the

key.

2. Using the  key, scroll through the menu until you find the CHANGE OPTIONS submenu.

3. Press the

key

4. Using the  key, scroll through the menu until you find the REPLACE BATTERY function.

5. Press the

key

6. Using the  key, find the name of wireless keypad in which you want to replace the

battery.

7. Press the

key

. The status of tamper switch in the keypad will not be checked for 3

minutes, which allows you to replace the battery.

5.13 Programming the partition timer

The partition timer automatically arms / disarms the partition.

1. Enter the code and confirm with the

key

2. Using the  key, scroll through the menu until you find the CHANGE OPTIONS submenu.

3. Press the

key

4. Using the  key, scroll through the menu until you find the PART. TIMERS function.

5. Press the

key

. The list of partitions will be displayed.

6. Using the  and  keys, find in the list the partition for which the timer is to be

programmed.

7. Press the

key

8. When the ACTIVE option is displayed, make sure it is enabled (the

symbol is displayed

next to the option). If it is not enabled (the

symbol is displayed next to the option), press

any digit key.

9. Using the  key, scroll through the menu until you find the TYPE function.

10. Press the

key

11. Using the  and  keys, select the timer type:

everyday – if the partition is to be armed / disarmed at the same time every day,

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Satel Integra 64 Seite 36

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Satel Integra 64

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info