Bedienungsanleitung Satel Integra 64 (Seite 37 von 51) (Englisch)

699075

Zoom out

Zoom in

Vorherige Seite

1/51

Nächste Seite

SATEL INTEGRA 35

weekly – if the partition is to be armed / disarmed at different times on different days of

the week.

12. Press the

key

13. If you have selected the daily variant, the function will allow you at once to program the

arming time, and upon pressing the  or  key – the disarming time. Upon confirmation

with the

key, you will be brought back to the list of options and functions.

14. If you have selected the weekly variant, you will be brought back to the list of options and

functions, where functions will appear to enable programming of the arming / disarming

time for each day of the week (in the same way as for daily timer).

Programming the value 99:99 means that the partition will not be armed / disarmed.

15. After the arming time has been programmed, an additional function will be displayed,

which allows you to define which arming mode will be activated by the given timer. By

default, the timer activates the full arming mode. If another arming mode is to be

activated, run this function (for the daily timer or individually for each day of the week)

and, using the  and  keys, select another arming mode. Confirm, using the

key.

16. Having programmed all parameters, press the

key.

17. When a prompt appears, asking you if the changes are to be saved, press the 1 key.

5.14 Zone testing

Within periodic inspections of the security alarm system, the detectors must be checked for

proper functioning. The zone testing function will allow you to do it without triggering the

reaction normally expected on violation, which is of particular importance in case of

permanently armed zones.

1. Enter the code and confirm with the

key

2. Using the  key, scroll through the menu until you find the TESTS submenu.

3. Press the

key

4. Using the  key, scroll through the menu until you find the ZONES TEST submenu.

5. Press the

key

6. When the NEW function is displayed, press the

key.

7. Select whether burglary zones or fire and technical zones, or single zone, will be tested,

and then press the

key.

8. Select the partitions in which zones will be tested (see: “Selection from the multiple-choice

list” p. 16).

9. Specify the test duration (maximum 50 minutes) and press the

key.

10. Define, whether violation of a zone is to trigger CHIME in the keypad (if yes, press any

numeric key – the symbol will be displayed).

11. Press the

key

. The zone test will start.

Beginning of the zone test in any partition will start the test mode in all ABAX 2 / ABAX

system wireless devices which are used together with the control panel (the wireless

detectors will signal violations by means of LEDs).

If any detectors with remote LED ON/OFF function are connected to the control panel,

you can switch on the LEDs in them for the test duration (the installer can configure

the control panel so that this will take place automatically at the beginning of the test).

You can terminate the zone test before expiration of the programmed time, using the

FINISH TEST function (TESTS ZONE TEST FINISH TEST). Up to 6 seconds can elapse

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Satel Integra 64 Seite 37

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Satel Integra 64

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info