Bedienungsanleitung Satel MICRA (Seite 19 von 52) (Englisch)

699548

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

SATEL MICRA 17

Power 12V DC – enabling this option will result in switching off the built-in power supply,

its control system, and in disconnecting the battery. In order to connect and external

power source to the device, connect the common ground to the COM terminal on the

module electronics board, and 12 V DC voltage to the AUX terminal.

If the “Power 12V DC” option is enabled, do not connect battery to the module.

Entry delay – parameter available in the alarm device mode, denoting the time by which

the alarm will be delayed when an armed zone of the 4. D

ELAY

type is violated. It

enables the zone to be disarmed before an alarm is triggered. You can program up to

255 seconds. If value 0 is programmed, violation of the armed 4. D

ELAY

zone type will

trigger an instant alarm.

Exit delay – parameter available in the alarm device mode, denoting the time counted

from the moment of arming. Violation of a 0. I

NSTANT

or 4. D

ELAY

zone type during the

exit delay countdown will trigger no alarm, which allows you to leave the protected area

without setting off alarm. You can program up to 255 seconds. If value 0 is

programmed, all zones will be instantly armed.

AC loss report delay – the time during which the module AC power must be lost for

a trouble to be reported. The trouble report delay prevents momentary outages, which

do not affect the normal operation of the module, from being reported. You can program

up to 99 minutes and 99 seconds.

Zones

Working parameters for hardwired and wireless zones are programmed in separate tables.

Wired zones

Name – individual name of zone (up to 16 characters).

Type – you can program the following wiring types (you can make your selection in the

right-click drop-down menu, or by entering a digit corresponding to the wiring type):

0. disabled – select this type, if no device is connected to the zone;

1. NC – select this type, if a device with normally closed contacts is connected to the

zone;

2. NO – select this type, if a device with normally open contacts is connected to the

zone;

3. – depending on the operating mode:

 communication device: 3. analog – select this type, if the zone is to supervised

analog signals;

 alarm device: 3. EOL 2k2 – select this type, if a 2.2 k EOL resistor is used.

Sensitivity – time during which:

– the NC type zone must be disconnected from the ground so that the module can

– the NO type zone must be shorted to ground so that the module can register the

zone violation,

– the EOL type zone must be shorted to ground or disconnected from the ground so

that the module can register the zone violation,

– voltage on the analog zone must drop below threshold L (minus tolerance) or rise

above threshold H (plus tolerance) so that the module can register exceeding the

preset value (see Fig. 10).

Values from the 0 to 5100 ms range can be programmed (every 20 ms).

Restore – time during which:

– the NC type digital zone must be again shorted to ground so that the module can

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Satel MICRA Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Satel MICRA

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info