Bedienungsanleitung Satel MICRA (Seite 24 von 52) (Englisch)

699548

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

22 MICRA SATEL

Output 1 / 2

Control of the outputs by means of commands sent in SMS messages is possible in the

communication device mode and, for the C

ONTROLLED

type outputs, in the alarm device

mode.

Turn on – content of the control command which will be used to activate the relay output.

Turn off – content of the control command which will be used to deactivate the relay

output.

Turn on for period – content of the control command which will be used to activate the

relay output for a period of time (the cut-off time must be defined for the output).

Zones

Bypass – content of the control command that must be included in the SMS message

being sent to the module for the zones to be bypassed (blocked). Depending on the

module operating mode:

communications device – all zones with the “Blocked” option enabled will be blocked.

alarm device – the zones specified in the received SMS message will be bypassed.

The SMS message should have the following form: xxxx=n= (where “xxxx” is the

command, defined in the “Bypass” field, starting the zone bypassing function in the

module; “n” is the number of zone to be bypassed – where two or more zones are to

be bypassed, they must be separated by commas and then the command should

have, for example, the following form: bypass=1,2,3= ). The zone will remain

bypassed until it is unbypassed by using the control command received in the SMS

message.

Unbypass – content of the control command that must be included in the SMS message

being sent to the module for the zones to be unbypassed (unblocked). Depending on

the module operating mode:

communications device – all blocked zones will be unblocked.

alarm device – zones specified in the received SMS message will be unbypassed. The

SMS message should have the following form: yyyy=n= (where “yyyy” is the

command, defined in the "Unbypass" field, starting the zone unbypassing function in

the module; “n” is the number of zone to be unbypassed – where two or more zones

are to be unbypassed, they must be separated by commas and then the command

should have, for example, the following form: unbypass=1,2,3= ).

The armed zones cannot be bypassed / unbypassed (alarm device mode).

Options

The module can be c

ontrolled by using SMS messages. The control commands should be

defined in consecutive tabs. The SMS message to be sent to the module may only contain

one control command. The control command can be composed of up to 24 characters.

SMS control only from list of telephone numbers for messaging – if the option is

enabled, only the SMS messages sent from authorized telephone numbers will allow:

– control (arming/disarming, alarm clearing, bypassing/unbypassing zones,

activating/deactivating outputs),

– changing the content of text messages used for SMS notifications.

The telephone numbers must be included in the “Telephone numbers for messaging

and test transmissions” list.

Confirm controlling with status SMS – if this option is enabled, starting the control

function (arming/disarming, alarm clearing, bypassing/unbypassing zones,

activating/deactivating outputs) will result in sending by the module of an SMS message

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Satel MICRA Seite 24

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Satel MICRA

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info