Bedienungsanleitung Satel MICRA (Seite 22 von 52) (Englisch)

699548

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

20 MICRA SATEL

Blocking – option available for the communication device mode. If enabled, the zone will

function as a blocking zone, i.e. its violation will result in blocking other zones of the

module. Only one module zone from among the wired and wireless ones can perform

the function of blocking zone.

Blocked – option available for the communication device mode. If enabled, the zone will

be blocked upon violation of a blocking zone or after receiving by the module of

a suitable control command in SMS message (content of the command being defined in

the "Bypass" field).

Zone type – parameter available for the alarm device mode. One of the zone types

described in section “Wired zones” can be selected. You can make your selection in the

dropdown menu which will be displayed after a right-click of your mouse, or by entering

the digit corresponding to the zone type.

Output 1 / 2 – fields available for the communication device mode. They allow you to

define, if and how the zone will control the output. Click on the field twice to display

successively:

– blank field – zone does not control the output,

– ON – violation of the zone will activate the output,

– ON for a time – violation of the zone will activate the output for a defined time (cut-

off time must be defined for the output),

– OFF – violation of the zone will deactivate the output.

Presence check – select the field (the field is selected, when the “x” symbol is shown in

it), if the module is to control presence of the detectors. The module will then analyze

the transmissions sent periodically by the detectors. In the field, the number of packets

received during the last transmission will be shown in parentheses (up to 18). In the

main menu, under the fields corresponding to the particular wireless zones, bars will

appear to illustrate the quality of communication. The shorter the bar and the lower the

number in parentheses, the lower the communication quality. If the field is selected and

the module receives no transmission from a detector for one hour, a trouble will be

reported by the module – the suitable message will be displayed in the GPRS-S

OFT

program (default: the option is disabled).

New detector – the button allows you to add a wireless detector (see: Adding new

wireless devices). If a detector has already been added in the given position, a window

will open with a prompt, whether the detector should be replaced with a new one. If the

answer is affirmative, click “OK” to bring up the new detector adding window. The type

and serial number will be replaced, but the name and the zone type assigned to the old

detector will be retained.

Remove detector – the button allows you to remove a wireless detector (see: Removing

wireless devices).

Test Mode ON / OFF – the button allows y

ou to start / end the test mode in the module.

The test mode enables the wireless and hardwired detectors to be checked for correct

functioning. Detector violation will result in setting the module relay outputs to 300 ms (it

applies to all output types, except for the “no” type). If a signaling device is connected to

the output, each violation of the detector will be suitably signaled. On starting the test

mode, the bars indicating the quality of communication in the main menu for the

wireless detectors will change their color to red, and number 0 will be displayed in the

"Presence check" fields. Only after receiving transmission from a wireless detector will

the information on communication quality be displayed. The test mode will automatically

be ended after 30 minutes. Arming will end the test mode.

Starting the test mode will block signaling the alarm triggered from the TMP zone

programmed as type 1. 24h as well as the tamper alarms triggered by the wireless

detectors and the wireless keypad.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Satel MICRA Seite 22

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Satel MICRA

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info