Bedienungsanleitung Satel PERFECTA 16-WRL (Seite 18 von 27) (Englisch)

699465

Zoom out

Zoom in

Vorherige Seite

1/27

Nächste Seite

16 PERFECTA SATEL

Do not connect two devices with power supply to one-section transformer.

Before connecting transformer to a circuit from which it will be powered, make

sure the circuit is de-energized.

6.9.2 Backup power supply

A 12 V lead-acid sealed battery should be connected to the control panel as a backup power

source. The battery capacity must be adequately selected to match current consumption in

the system. According to EN 50131 Grade 2, the battery must ensure operation of the system

without mains supply for 12 hours.

If the battery voltage drops below 11 V for longer than 12 minutes (3 battery tests), the

control panel will indicate battery failure. When the voltage goes down to approx. 10.5 V, the

battery will be disconnected.

Do not connect deeply discharged battery to the control panel (with voltage

across unloaded terminals below 11 V). The battery should be precharged with

a proper charger.

The used batteries must not be discarded, but should be disposed of in

accordance with the existing rules for environment protection.

6.9.3 Control panel power-up / start-up procedure

1. De-energize the 230 V AC circuit to which the transformer is to be connected.

2. Connect the 230 V AC wires to the terminals of transformer primary winding.

3. Connect the terminals of transformer secondary winding to the control panel AC

terminals. To make the connection, use flexible conductors with a cross-section of 0.5 –

0.75 mm

, or rigid conductors with a cross-section of 1 – 2.5 mm

4. Connect the battery to the dedicated leads (positive terminal to RED lead, negative

terminal to BLACK lead). If the battery has screw-type cable lugs, use adapters delivered

with the control panel (do not cut off the battery cable lugs). The control panel will not

start after connecting the battery alone.

5. Turn on 230 V AC power supply in the circuit to which the transformer is connected.

The control panel will start operating.

The above mentioned power-up sequence (first the battery, then the 230 V AC mains)

will ensure proper operation of the power supply unit and the electronic protection

circuits, thus preventing damage to the alarm system components caused by

installation mistakes, if any.

If it is necessary to de-energize the control panel, turn off the main power supply (AC)

first, and the backup power supply (battery) afterwards. Observe the above described

procedure when reconnecting the power supply.

6.9.4 Starting the service mode

If, after starting the alarm control panel, you want to perform any operations that not require

power-off (e.g. to adjust sensitivity in wired detectors), enter the service mode.

When the control panel is running in service mode, tamper alarms are not

generated.

1. Enter the service code (by default: 12345) and press .

2. User menu appears.

3. Press .

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Satel PERFECTA 16-WRL Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Satel PERFECTA 16-WRL

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info