Bedienungsanleitung Satel PERFECTA 16-WRL (Seite 19 von 27) (Englisch)

699465

Zoom out

Zoom in

Vorherige Seite

1/27

Nächste Seite

SATEL PERFECTA 17

4. When the cursor shows the S

ERVICE MODE

function, press .

5. Service mode menu will be displayed (the cursor will show the E

SM function).

6.9.5 Emergency procedure of the control panel start-up

If the control panel fails to start properly, keypads are not supported, codes are not accepted

by the control panel etc., despite all connections having been made correctly, follow the steps

below:

1. Turn off the control panel power supply (first disconnect the AC power, and then the

battery).

2. Put a jumper on the RESET pins.

3. Turn on the control panel power supply (first connect the battery and then the AC power).

4. Wait a few seconds (until LEDs next to the RESET pins stop blinking) and remove the

jumper from the RESET pins. The control panel will enter the service mode. The service

mode menu will be displayed on the wired keypad with the lowest address.

If there is no wired keypad in the alarm system or there is no communication with the

wired keypads (e.g. when the communication bus is shorted), you can get access to

the service mode menu from the wireless keypad with the lowest address. Press any

key on this keypad within 30 seconds of removing jumper from the RESET pins.

The service mode menu will not be displayed, if the D

ISABLE

ERVICE

ODE

option is

enabled in the control panel. The “Factory settings ? 1=Yes” message will be

displayed on the keypad with the lowest address. You can press to restore the

factory default settings. The service mode menu will not be displayed until the factory

settings are restored.

6.9.6 First steps after starting-up the control panel

Control panel with wired keypads

If wired keypads are connected to the control panel, then, after starting the control panel with

factory settings:

1. Set correct, individual addresses in the wired keypads.

2. Run the function of identification of devices connected to the communication bus of the

control panel.

Control panel without wired keypads PERFECTA 16-WRL / PERFECTA 32-WRL

If no wired keypads are connected to the control panel, then, after starting the control panel

with factory settings:

1. Connect computer to alarm control panel.

2. Use the PERFECTA

OFT

program to add wireless keypads.

3. Run the function of identification of devices connected to the communication bus of the

control panel.

6.10 Programming addresses for the hardwired keypads

An individual address from the 0 to 3 range must be set for each keypad. By default, address

0 is preset for all wired keypads. After starting the alarm control panel with factory default

settings, all keypads connected to the bus are supported, no matter what their addresses are.

This allows you to program individual address for the keypads.

Remember to program an individual address if a new keypad is connected to the

already functioning alarm system.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Satel PERFECTA 16-WRL Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Satel PERFECTA 16-WRL

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info