Bedienungsanleitung Satel PERFECTA 16 (Seite 34 von 49) (Englisch)

699464

Zoom out

Zoom in

Vorherige Seite

1/49

Nächste Seite

32 PERFECTA SATEL

– 13. Z

ONE VIOLATION

output will be active when the zone is violated,

– 15. C

ONTROLLED

output will remain active until repeated zone violation, stopping timer or

deactivating from keypad, etc.

Triggering zones [43.Zones] – the zones whose status has effect on the output status.

Arming modes [43.Zones] – arming modes which affect the output status.

Troubles [43.Zones] – troubles during which the output is active.

Assigned to part. 1 [451.P.1 outputs] – if this option is enabled, the output is controlled by

events related to partition 1 (alarm in partition 1, clearing alarm in partition 1 etc.).

Assigned to part. 2 [452.P.2 outputs] – if this option is enabled, the output is controlled by

events related to partition 2 (alarm in partition 2, clearing alarm in partition 2 etc.).

Polarity + [453.Polarity(+)] – the option defines how the outputs will operate (see the table

below). If the option is disabled, the output is inverted. The option does not apply to

wireless outputs.

“–” terminal of high-current output / low-current output

option enabled

(normal polarity)

option disabled

(reverse polarity)

output inactive

disconnected from ground shorted to ground

output active

shorted to ground disconnected from ground

Table 2. Mode of output operation depending on the P

OLARITY

+ option.

Pulsed [454.Pulsed] – if this option is enabled, the output is pulsating when it is active. The

option does not apply to the 1. E

XTERNAL SIREN

, 2. I

NTERNAL SIREN

, 11. F

IRE DETECTORS

OWER SUPPLY

and 20. A

ALARM STATUS OUTPUTS

. The option does not apply to wireless

outputs.

Arm/Disarm/clear sign. [455.Arm/Dis/Clr] – if this option is enabled, the output will signal:

– starting the arming procedure (if the exit delay time is 0, the system is armed

immediately) – 1 pulse,

– disarming – 2 pulses,

– clearing alarm – 4 pulses,

– denial of arming or arming procedure failure – 7 pulses.

The signaling is triggered if a keyfob or zone is used to arm / disarm the system or clear

alarm. Pulse duration is about 0.3 second. Option for the 1. E

XTERNAL SIREN

, 2. I

NTERNAL

SIREN

, 3. B

URGLARY

, 4. FIRE

ALARM

, 5. DURESS

ALARM

, 6. PANIC

ALARM

, 7. MEDICAL

ALARM

, 8. A

LARM

NOT VERIFIED

, 9. A

LARM

VERIFIED

and 10. T

AMPER ALARM

outputs.

Triggering timers [44.Timers] – the output control timers (starting the timer activates the

output). The parameter refers to the 15. C

ONTROLLED

output.

7.3 Quick control of outputs

If the quick control of the outputs 15. C

ONTROLLED

is to be available in keypads, the outputs

of this type must be assigned to the corresponding keypad keys. One output can be assigned

to each number key.

7.4 Wireless siren PERFECTA 16-WRL / PERFECTA 32-WRL

If a wireless siren is assigned to the output, additional parameters and options are available

(outputs 13-16).

Filter [1272.Filter] – time counted from the moment of receiving transmission from the siren.

After it has elapsed and no other transmission is received, trouble will be reported.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Satel PERFECTA 16 Seite 34

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Satel PERFECTA 16

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info