Bedienungsanleitung Satel VERSA 10 (Seite 28 von 36) (Englisch)

699459

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

26 VERSA SATEL

5.12.1 Starting the identification function from keypad

1. Enter the service code (by default 12345) and press the key.

2. Press in turn the keys. The service mode will start.

3. Press in turn the keys. The IDENTIFICATION function will start.

Three short beeps will indicate that identification has been completed and information on

the identified devices will be presented (on the display in the LCD keypad and by means

of LEDs in the LED keypad).

4. Press the key to quit the function.

If the identification is terminated by two long beeps, this means that a wrong address

is set in the device connected to the communication bus (unsuitable for this type of

device or the same in at least two devices). The displayed message (in the LCD

keypad) or the blinking LED corresponding to the device address (in the LED keypad)

will be helpful in diagnosing the problem. Press , set the correct address in the

device, and then restart the IDENTIFICATION function.

5.12.2 Starting the identification function from DLOADX program

1. Click on the button in the main menu. The “VERSA – Structure” window will open.

2. Click on the “Hardware” tab.

3. Click on the “Expanders” branch.

4. Click on the “Identification” button to run the identification function.

5. After the identification is finished, a window will appear with a prompt whether to read the

data. Click “OK”.

5.13 Connecting the computer to the control panel

Using a computer, you can configure the alarm system (DLOADX program) or update the

control panel firmware. The communication is encrypted. The RS-232 port (TTL) of the

control panel can be connected with the USB port of the computer by means of the USB-RS

converter offered by SATEL.

5.14 Installation of ABAX wireless devices

This section does not cover installation of the wireless keypads. They constitute

a separate category of devices and should be installed according to the manual

delivered with the device.

If an ABAX wireless system controller (ACU-120 / ACU-270 / ACU-100 / ACU-250) is

connected to the control panel, you can proceed to installation of ABAX wireless devices

after control panel start-up and controller identification by the control panel. Before installing

a wireless device, check the level of radio signal received by the device from controller and

by the controller from device at the planned installation place. The ARF-100 tester is a useful

tool to check the signal level. The level of signal received by device/controller may not be

lower than 40%. If the radio signal level at the planned installation place is too low, select

another installation location. Sometimes it is sufficient to move the device ten or twenty

centimeters to obtain a significant improvement of signal quality. You can install the device

permanently only after reaching the optimum level of radio signal.

The wireless devices must be registered to the alarm system. This can be done using the

DLOADX program or LCD keypad.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Satel VERSA 10 Seite 28

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Satel VERSA 10

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info