Bedienungsanleitung Satel VERSA 10 (Seite 29 von 36) (Englisch)

699459

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

SATEL VERSA 27

5.14.1 Adding new ABAX wireless devices

The control panel can support up to 30 wireless devices. The number of actually supported

devices depends on how many positions the individual devices occupy. Each position means

one wireless zone or one wireless zone and one wireless output.

If a device occupies two or more positions, its addition will respectively decrease the number

of wireless devices that can still be registered (e.g. after adding a ACX-200 expander, which

takes up 4 positions, the controller can still support 26 other wireless devices).

Even if a device occupies several zones in the system, only the first of them should be

indicated during the device adding procedure. The next ones are assigned automatically

(these are the zones following the selected one).

For some wireless devices, you can select whether the device will take up one or two

positions (channels) on the list of devices. Depending on the device, if one position is

selected:

 AMD-101 – only additional NC input will be supported,

 AMD-102 – only additional inputs (roller shutter and NC) will be supported;

 AOD-200 – only the motion detector will be supported;

 AVD-100 – only the vibration detector will be supported.

If the device occupies an output as well, its number will be the same as the number of zone

selected during the device adding procedure.

The control panel does not support wireless outputs with numbers from 13 to 30.

DLOADX program

You can add ABAX wireless devices in the “VERSA – Structure” window, “Hardware” tab,

after clicking on the ABAX system controller name in the list of devices.

1. In the “Zones/Outputs” tab, click on the “Read” button to read the data related to wireless

devices from the controller (these data are not read after clicking on the button in

the main menu).

2. Click on the zone to which a new wireless device is to be assigned (you can also select

the zone later in the “New wireless dev.” window).

3. Click on the “New device” button. The “New wireless dev.” window will open.

4. Enter the 7-digit serial number of the added device. The serial number can be found on

the electronics board or on the enclosure. Each ARF-100 radio signal level tester has

serial number 0000500.

5. Depending on the device type:

ACX-200 / ACX-201: power-up the expander,

ARF-100: turn on the device,

ASW-100 E / ASW-100 F: insert the controller into 230 V AC socket,

other devices: open the tamper contact.

6. The message will confirm that a new device has been added (unless you have entered an

invalid serial number, of which you will be informed by a message). The new zone name

will be displayed. You can change it. The same name will also be given to the output, if

the device is assigned to the output.

7. Click on the “OK” button (you can click on the “Quit” button to cancel adding a new device

or on the “Next” button to proceed to adding a next wireless device).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Satel VERSA 10 Seite 29

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Satel VERSA 10

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info