Bedienungsanleitung Satel VERSA 10 (Seite 31 von 36) (Englisch)

699459

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

SATEL VERSA 29

5.15 Installation of 433 MHz wireless detectors

If the 433 MHz wireless system controller (VERSA-MCU) is connected to the control panel,

you can proceed to installation of the 433 MHz wireless detectors after control panel start-up

and controller identification by the control panel. Before installation of the detector, register it

in the controller and check, if transmissions from the detector located at the planned

installation place can reach the controller. To send a transmission, you can e.g. open the

detector tamper switch. If transmissions from the detector planned installation place do not

reach the controller, select another location. Sometimes, it is sufficient to move the detector

by some ten to twenty centimeters. Only after making sure that the controller receives

transmissions from the detector, you can install the detector permanently.

The wireless detectors must be registered to the alarm system. This can be done using the

DLOADX program or LCD keypad.

5.15.1 Adding new 433 MHz wireless detectors

The control panel can support up to 30 wireless detectors.

DLOADX program

You can add 433 MHz wireless detectors in the “VERSA – Structure” window, “Hardware”

tab, after clicking on the VERSA-MCU controller name in the list of devices.

1. Click on the “Read” button to read the data related to wireless detectors from the

controller (these data are not read after clicking on the

button in the main menu).

2. Click on the zone to which a new wireless detector is to be assigned (you can also select

the zone later in the “New wireless dev.” window).

3. Click on the “New device” button. The “New wireless dev.” window will open.

4. Enter the 7-digit serial number of the added detector. The serial number can be found on

the electronics board or on the enclosure.

5. Open the detector tamper contact.

6. The message will confirm that a new detector has been added (unless you have entered

an invalid serial number, of which you will be informed by a message). The new zone

name will be displayed. You can change it.

7. Click on the “OK” button (you can click on the “Quit” button to cancel adding a new

detector or on the “Next” button to proceed to adding a next wireless detector).

8. Click on the “Write” button to write the new wireless detector data to the controller (these

data will not be written after clicking on the button in the main menu).

LCD keypad

You can add the 433 MHz wireless detectors in the service mode by means of the NEW

DEVICE

function (SERVICE MODE 2. HARDWARE 1. KPDS. & EXPS. 3. WIRELESS MOD.

1. NEW DEVICE).

1. Having started the function, enter the 7-digit serial number of the added detector and

press the key. The serial number can be found on the electronics board or on the

enclosure.

2. Open the detector tamper contact.

3. Information on the detector to be added will be displayed (if nothing happens, it can mean

that you have entered an invalid serial number – if this is the case, press to return

to the submenu). Press to confirm your intention to add a detector.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Satel VERSA 10 Seite 31

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Satel VERSA 10

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info