Bedienungsanleitung Satel VERSA 15 (Seite 30 von 87) (Englisch)

699458

Zoom out

Zoom in

Vorherige Seite

1/87

Nächste Seite

28 VERSA SATEL

– in case of arming by means of the LCD keypad, the control panel will check if there are

any zones bypassed in the partition – information on the bypassed zones is presented,

if the user has the INSPECTION right,

– the warning alarm feature is enabled in the system (see: WARNING ALARM global option),

– the warning alarm is signaled at the 2. INTERNAL SIREN function output (ref. WARNING

ALARM ON INTERNAL SIRENS

global option).

You can enable/disable the option in keypad: SERVICE MODE 2. HARDWARE 1. KPDS &

EXPS

. 4. OPTIONS GRADE2.

Serial data on OUT 3/4 – if the option is enabled, OUT3 and OUT4 outputs send the system

status data (zone alarms, fire alarms, troubles, armed modes, etc.) and do not execute any

other programmed functions. The outputs may be used to control the NR2-DSC radio

monitoring transmitter (NEMROD system – PC-16 OUT format), made by NOKTON.

OUT 3/4 data extended mode – if the option is enabled, the OUT3 and OUT4 outputs will

send the system status data in the form of frames (PC-16 OUT UA format). The option is

available, if the SERIAL DATA ON OUT 3/4 option is enabled.

Arm./Disarm./Clear. signaling from zones only – if the option is enabled, outputs with the

functions 1. EXTERNAL SIREN and 2. INTERNAL SIREN with enabled ARM/DISARM/CLEAR SIGN.

option will signal only:

– starting of the arming procedure by zone or by means of keyfob,

– no possibility of arming (see: PREVENT ARMING IF NOT READY option or GRADE 2 option), if

the arming command has been sent from keyfob,

– failed attempt of arming by means of keypad or keyfob (see: PREVENT ARMING IF NOT

READY

option or GRADE 2 option),

– disarming by zone or by means of keyfob,

– alarm clearing by zone or by means of keyfob.

Starting the arming procedure, disarming or alarm clearing by means of keypad, proximity

card arm/disarm device or timer are not signaled.

Clear messaging on alarm clearing – if the option is enabled, clearing the alarm will

automatically cancel messaging about this alarm, if the user clearing the alarm has the

EL. MESS. CLEARING right.

Service message after tamper alarm – if the option is enabled, information on the tamper

alarm can only be cleared from the troubles memory by using the service code. In the LCD

keypad, the “System tamper, call service” message will be displayed after the tamper

alarm (unless the alarm messages are displayed). The message will no longer be

displayed after the troubles memory is reset by the service.

Warning alarm – if the option is enabled, the warning alarm feature is enabled. It purpose is

to delay the loud signaling and reporting, if any mistakes are made when entering the

protected facility. The warning alarm is not reported. It can be signaled on the keypad,

proximity card arm/disarm device or outputs with the function 2. I

NTERNAL SIREN. The

warning alarm is triggered by the following zone types:

– 0. ENTRY/EXIT or 1. ENTRY/EXIT FINAL – unless the system is disarmed before completion

of the ENTRY DELAY countdown,

– 2. ENTRY/EXIT ROUTE – if it is violated during the ENTRY DELAY countdown, and the

system is not disarmed before completion of the D

ELAY TIME countdown,

– 3. I

NSTANT – if it is violated during the ENTRY DELAY countdown.

The warning alarm lasts 30 seconds. Unless the alarm system is disarmed during this

time, the alarm will be triggered by the zone.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Satel VERSA 15 Seite 30

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Satel VERSA 15

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info