Bedienungsanleitung Satel VERSA 15 (Seite 32 von 87) (Englisch)

699458

Zoom out

Zoom in

Vorherige Seite

1/87

Nächste Seite

30 VERSA SATEL

seconds can be programmed. Programming the value 0 means that the LED will be lit as

long as the partition is armed.

AC loss report delay – time during which the control panel must be without AC power

before the trouble is reported. A delay in reporting the trouble prevents sending information

about short-time voltage decays, having no effect on normal operation of the system. The

trouble reporting delay can be up to 255 minutes.

Tel. line loss report delay – time during which abnormal voltage must be on the telephone

line for the control panel to report the telephone line trouble. A delay in reporting the

trouble prevents sending information about short-time voltage dips (e.g. during a phone

call) or decays. The trouble reporting delay can be up to 255 minutes.

RTC clock correction – if the accuracy of control panel clock is inadequate, the clock

settings may be adjusted once per 24 hours (at midnight) by a defined time. The maximum

correction can be ±19 seconds per 24 hours.

Summer/winter time – the control panel can automatically adjust the clock settings due to

a change from the summer time to the winter time and vice versa. The following correction

schemes are available:

– no correction,

– according to the European Union rules,

– according to the United States' rules,

– correction by 1 hour according to dates,

– correction by 2 hours according to dates.

Summer time from / Winter time from – if the control panel clock is to be corrected by 1 or

2 hours according to dates, you should enter the dates (day, month) after the clock is

changed to the summer time (moved forward) or to the winter time (moved back).

4.4 Arming

Prevent arming if not ready – when the option is enabled, if the user arm the system by

means of keypad or keyfob, the control panel checks that there are no circumstances that

prevent the arming:

– a zone with P

RIORITY option is violated in the partition which is to be armed,

– the 3. I

NSTANT, 4. DOUBLE KNOCK, 5. 24H BURGLARY, 6. 24H TAMPER, 7. 24H PANIC, 8. 24H

PANIC SILENT

, 9. 24H MEDICAL or 10. 24H FIRE type zone is violated in the partition which

is to be armed,

– there is a trouble in the system.

If one of the aforementioned situations takes place, the control panel will not start the

arming procedure (the LCD keypad enables forced arming – see: U

SER MANUAL). If none of

the conditions is met, the control panel will start the arming procedure, but at the end of

the exit delay countdown it will check again if the arming is possible (the quick arming

being an exception). A violated zone or a trouble mean that the arming is not possible (i.e.

the arming procedure will fail).

Additionally, when the option is enabled and the user has the INSPECTION right, the LCD

keypad will inform, prior to arming, that there are bypassed zones in the partition (it does

not apply to the quick arming).

You can enable/disable the option in keypad: S

ERVICE MODE 2. HARDWARE 1. KPDS &

EXPS

. 4. OPTIONS ADVANCED ARMING.

Arm even if not ready after exit delay – if the option is enabled, a zone violation or trouble

found at the end of exit delay countdown does not affect the arming procedure – the

system will be armed. You can enable/disable the option in keypad: SERVICE MODE

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Satel VERSA 15 Seite 32

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Satel VERSA 15

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info