Bedienungsanleitung Satel Versa IP (Seite 64 von 93) (Englisch)

629722

Zoom out

Zoom in

Vorherige Seite

1/93

Nächste Seite

62 VERSA IP SATEL

1. Enter a number from the 0 to 50 range to define the rules of device presence control, and

then press .

2. Use the and keys to define how the acoustic signaling will work (

–

disabled; 1, 2 or 3 – type of acoustic signaling), and then press .

3. Use the and keys to define the maximum duration of signaling, and then

press .

4. Define whether the optical signaling is to be enabled ( – no, – yes), and then press

ASW-100 E / ASW-100 F controller

1. Enter a number from the 0 to 50 range to define the rules of device presence control, and

then press .

2. Use the and keys to define mode of operation of the button (“inactive” – the

electric circuit is controlled remotely only; “interim control” – the electric circuit can be

controlled remotely or manually; “combined control” – the electric circuit can be controlled

remotely or manually, but the remote control can be manually overridden), and then press

9.4.4 Specific character of the operation of wireless devices

This chapter describes the peculiar character of the operation of individual groups of wireless

devices, which affects the method of programming the zones and outputs to which the

wireless devices are assigned.

ABAX wireless detectors

The wireless detectors send information on violations, tampers and low-battery status. The

information on violations and tampers is sent to the zones to which the detectors are

assigned. You can program these zones as:

 NC, NO or EOL – the zone will inform about detector violation,

 2EOL/NC or 2EOL/NO – the zone will inform about detector violation and tamper.

The mode of operation of wireless detectors depends on the status of partition to which the

zone with wireless detector belongs:

partition disarmed – the detector operates in passive mode. It is a battery saving mode, in

which communication with the controller takes place mainly during time intervals

determined by the RESPONSE PERIOD parameter. At that time, information on violations and

battery status is sent. Only detector tampers are sent immediately.

partition armed – the detector operates in active mode. The detector sends immediately all

information to the controller.

Because switching the detectors over from the passive into active mode and conversely

takes place during the response time, it is performed with some delay in relation to

arming/disarming. The maximum delay – depending on the selected response frequency –

can be 12, 24 or 36 seconds.

The AMD-103 detector and the wireless detectors assigned to 24-h zones, i.e. always armed,

are in active mode at all times. Also other wireless detectors can always operate in active

mode, if the A

LWAYS ACTIVE option is enabled for them (see: “Parameters and options of

ABAX system wireless devices” p. 55).

According to the EN50131-3 standard all ABAX sy

stem Hold-Up devices must be

always in active mode.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Satel Versa IP Seite 64

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Satel Versa IP

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info