Bedienungsanleitung Satel Versa Plus (Seite 31 von 36) (Englisch)

699394

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

SATEL VERSA Plus 29

5.17.2 Removing ABAX wireless devices

DLOADX program

You can remove ABAX wireless devices in the “Versa – Structure” window, “Hardware” tab,

after clicking on the ABAX system controller name in the list of devices.

1. In the “Zones/Outputs” tab, click on the “Read” button to read the data related to wireless

devices from the controller.

2. Click on the zone to which the device you want to delete is assigned (if the device is

assigned to several zones, you can click on any of them).

3. Click on the “Delete” button. The “Confirm” window will open.

4. Click on the “Yes” button. The “Confirm” window will close.

5. Click on the “Write” button to save the changes to the controller.

LCD keypad

You can remove ABAX wireless devices in the service mode by means of the REMOVE DEVICE

function (SERVICE MODE 2. HARDWARE 1. KPDS. & EXPS. 3. WIRELESS MOD. 3. REMOVE

DEVICE

1. Having started the function, use the

and keys to select the zone to which the

wireless device to be removed is assigned, and then press .

2. A prompt will appear asking you whether the device is to be deleted (device type and

serial number will be displayed). Press . The device will be deleted.

5.18 Installation of 433 MHz wireless detectors

If the 433 MHz wireless system controller (VERSA-MCU) is connected to the control panel,

you can proceed to installation of the 433 MHz wireless detectors after control panel start-up

and controller identification by the control panel. Before installation of the detector, register it

in the controller and check, if transmissions from the detector located at the planned

installation place can reach the controller. To send a transmission, you can e.g. open the

detector tamper switch. If transmissions from the detector planned installation place do not

reach the controller, select another location. Sometimes, it is sufficient to move the detector

by some ten to twenty centimeters. Only after making sure that the controller receives

transmissions from the detector, you can install the detector permanently.

The wireless detectors must be registered to the alarm system. This can be done using the

DLOADX program or LCD keypad.

5.18.1 Adding new 433 MHz wireless detectors

The control panel can support up to 30 wireless detectors.

DLOADX program

You can add 433 MHz wireless detectors in the “Versa – Structure” window, “Hardware” tab,

after clicking on the VERSA-MCU controller name in the list of devices.

1. Click on the “Read” button to read the data related to wireless detectors from the

controller (these data are not read after clicking on the button in the main menu).

2. Click on the zone to which a new wireless detector is to be assigned (you can also select

the zone later in the “New wireless dev.” window).

3. Click on the “New device” button. The “New wireless dev.” window will open.

4. Enter the 7-digit serial number of the added detector. The serial number can be found on

the electronics board or on the enclosure.

5. Open the detector tamper contact.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Satel Versa Plus Seite 31

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Satel Versa Plus

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info