Bedienungsanleitung Satel Versa Plus (Seite 30 von 36) (Englisch)

699394

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

28 VERSA Plus SATEL

1. In the “Zones/Outputs” tab, click on the “Read” button to read the data related to wireless

devices from the controller (these data are not read after clicking on the button in

the main menu).

2. Click on the zone to which a new wireless device is to be assigned (you can also select

the zone later in the “New wireless dev.” window).

3. Click on the “New device” button. The “New wireless dev.” window will open.

4. Enter the 7-digit serial number of the added device. The serial number can be found on

the electronics board or on the enclosure. Each ARF-100 radio signal level tester has

serial number 0000500.

5. Depending on the device type:

ACX-200 / ACX-201: power-up the expander,

ARF-100: turn on the device,

ASW-100 E / ASW-100 F: insert the controller into 230 V AC socket,

other devices: open the tamper contact.

6. The message will confirm that a new device has been added (unless you have entered an

invalid serial number, of which you will be informed by a message). The new zone name

will be displayed. You can change it. The same name will also be given to the output, if

the device is assigned to the output.

7. Click on the “OK” button (you can click on the “Quit” button to cancel adding a new device

or on the “Next” button to proceed to adding a next wireless device).

8. Click on the “Write” button to write the new wireless device data to the controller (these

data will not be written after clicking on the button in the main menu).

LCD keypad

You can add ABAX wireless devices in the service mode by means of the NEW DEVICE

function (SERVICE MODE 2. HARDWARE 1. KPDS. & EXPS. 3. WIRELESS MOD. 1. NEW

DEVICE

1. Having started the function, enter the 7-digit serial number of the added device and press

the key. The serial number can be found on the electronics board or on the

enclosure. Each ARF-100 radio signal level tester has serial number 0000500.

2. When the “Open device tamper” message is displayed, depending on the device type:

ACX-200 / ACX-201: power-up the expander,

ARF-100: turn on the device,

ASW-100 E / ASW-100 F: insert the controller into 230 V AC socket,

other devices: open the tamper contact.

3. Information on the device to be added will be displayed (if nothing happens, it can mean

that you have entered an invalid serial number – if this is the case, press to return

to the submenu). Press to confirm your intention to add a device.

4. Using the and keys, select the zone to which the device is to be assigned

and then press .

5. The new name of the zone will be displayed. You can change it. The same name will also

be given to the output, if the device is assigned to the output. Press

to save the

name. If the device takes up several positions, the name-giving procedure must be

repeated for them.

6. In the next steps, you can configure the device (see the P

ROGRAMMING manual).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Satel Versa Plus Seite 30

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Satel Versa Plus

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info