Bedienungsanleitung Satel Versa Plus (Seite 24 von 110) (Englisch)

699394

Zoom out

Zoom in

Vorherige Seite

1/110

Nächste Seite

22 VERSA Plus SATEL

Reset command – the command to reset the modem. Typically, it is the ATZ command

(reset with restoration of the user's zero profile). Some modems may require using the

AT&F command (reset with restoration of the factory default settings).

Initializing – lines containing the modem initialization commands:

300 bps transmission – in the first line: E0V1Q0 – a command required for proper

operation of the modem. You should also add the operating mode selection: B0 or B1

(selection of transmission format: V.21 or Bell103), and the commands limiting

transmission rate over telephone line to 300 bps. These are commands specific for the

given modem model, e.g. N0S37=3, F1 or +MS=1,0,300,300 etc. Information on how to

limit the modem transmission rate is usually included in the device manual. The other

line should contain the following commands: S0=0S9=1S7=120S10=255.

CSD transmission – in the first line: E0V1Q0. The command to be entered in the second

line depends on the type of modem connected do computer:

analog modem: S0=0S7=120,

GSM modem: S0=0.

Control panel settings

Parameters and options related to modem communication are described in sections “Global

parameters” (p. 32) and “Built-in communication modules (VERSA-ETH)” (p. 54).

3.2.3 Ethernet / GPRS communication parameters

Programming the parameters

DLOADX program settings

You can configure the Ethernet / GPRS communication settings in the “Identifiers and tel. no”

window.

Control panel settings

You can configure the Ethernet / GPRS communication settings when programming the built-

in communication modules (see: “Built-in communication modules (VERSA-ETH)” p. 54).

Description of the parameters

DLOADX program settings

Connection – you can define two sets of parameters:

LAN/WAN – parameters for communication via local or wide network.

LAN: VERSA-ETH – parameters for communication via local network only. In this case,

the port number and data encryption key programmed in the settings of built-in

communication modules will be used during communication.

Server – address of the control panel. If the control panel is not in the same local network as

the computer with DLOADX program, it must be a public address. You can enter either the

IP address or the domain name.

Port – the number of TCP port used for communication between the control panel and

computer with DLOADX program via Ethernet / GPRS. You can enter a value from 1 to

65535. Default value: 7090.

DLOADX key – a string of up to 12 alphanumeric characters (digits, letters and special

characters), used for data encryption during communication between the control panel and

the computer with DLOADX program via Ethernet / GPRS.

ETHM-1 ID – individual identification number of the control panel for the purpose of

communication via the SATEL server.

ETHM-1 MAC – hardware address of built-in Ethernet module.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Satel Versa Plus Seite 24

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Satel Versa Plus

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info