Bedienungsanleitung Satel Versa Plus (Seite 60 von 110) (Englisch)

699394

Zoom out

Zoom in

Vorherige Seite

1/110

Nächste Seite

58 VERSA Plus SATEL

PIN [SIM 1 PIN code / SIM 2 PIN code] – PIN code of the SIM card.

If a wrong PIN code is programmed, a trouble will be reported after using it. After 255

seconds the control panel will retry to use the PIN code. After the third attempt to use

a wrong PIN code, the SIM card will be blocked. To unblock the card, remove it and

insert into a cell phone, and then enter the PUK code.

GPRS APN – access point name for Internet GPRS connection.

Username – user name for Internet GPRS connection.

Password – password for Internet GPRS connection.

DNS server – IP address of DNS server to be used by the module.

The GPRS parameters can be obtained from the GSM network operator.

SMS center no. – telephone number of the short message service center. It is used as a

connecting link when sending SMS messages. If the number has been saved by the

operator to the SIM card memory, it need not be programmed. Otherwise, if the control

panel is to send SMS messages, it must be entered. The number must be suitable for the

operator of network in which the SIM card is registered.

Lock time – the time during which switch-over to the other SIM card is impossible. For

reporting, the transmission paths programmed as subsequent ones, if they require switch-

over to the other card, will be skipped during the lock lime countdown (see: “Transmission

priority” p. 82). Entering the value 0 means that instant switch-over to the other SIM card is

possible.

Return time – the time after which the other SIM card is to be used. Entering the value 0

means that automatic switch-over to the other SIM card will not take place.

If two SIM cards are to be used, one of them must be treated as the priority card. It is

recommended that return time equal to 0 be programmed for it.

USSD retransmit code

SMS – control command that will be sent in the SMS message together with USSD code.

The control panel will run the USSD code and send the response received from the

operator to the phone number from which the SMS message with control command was

sent. You can enter up to 8 alphanumeric characters (you can use spaces, but at least one

character must be different from the space). Owing to the USSD codes you can, for

example, check the account balance of SIM card installed in the control panel.

It is not advisable to use the advanced functions available due to the USSD service if

menu is presented in response to the entered code.

any number [USSD - any tel.] – if the option is enabled, the SMS messages containing

USSD codes can be sent from all telephone numbers. If the option is disabled, only from

the phone numbers included in the T

ELEPHONE NUMBERS table.

Answering (GSM)

Audio call answering – if the option is enabled, the module receives the incoming voice

calls.

Any number for audio – if the option is enabled, the module receives all incoming voice

calls. If the option is disabled, only from the phone numbers included in the TELEPHONE

NUMBERS

table.

Data call answering – if the option is enabled, the module receives the incoming modem

connections (CSD data transmissions).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Satel Versa Plus Seite 60

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Satel Versa Plus

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info