Bedienungsanleitung Scan 66 series (Seite 30 von 36) (Englisch)

745567

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

Continuous firing

It is important to reach as high a temperature as possible in the

combustion chamber. This makes the most efficient use of the wood

stove and fuel, and ensures a clean burning process. At the same

time, this avoids soot build-up on the combustion chamber walls and

glass. While the stove is lit, you should not see any smoke, but just air

movement that indicates the burning process.

After completing the lighting phase, you should have a good layer of

embers in the wood stove; you can then start stoking up the stove.

Lay 1-3 pieces of wood, of about max 1,7 kg weight with max 10 cm

diameter and a length of about 25 cm onto the fire.

Note! The wood must catch fire quickly; this is why we recommend

setting the primary airflow to full power. Running the stove at too

low a temperature and with too little primary air can lead to defla-

gration of the gases, and thus cause damage to the stove.

When stoking up with wood, always open the glass door carefully to

avoid smoke escaping. Never stoke up with wood while the fire is still

burning nicely.

Environmentally-Friendly Heating

Avoid restricting your wood-burning stove to an extent where no

flames are visible during the degasifying period, as this leads to

particularly inefficient heating. The gases released by the wood

do not burn due to the low temperature in the combustion cham-

ber. Part of the gas condenses in the wood-burning stove and flue

system as soot, and this could lead to your chimney catching fire.

The smoke that exits the chimney is bad for the environment and

has an unpleasant smell.

Lighting

We recommend the use of fire starters, or similar products, which are

available from your Scan dealer. Using fire starters helps to light the

wood quicker, and keeps the burning process clean.

Never use liquid lighting fuels!

"Top down" lighting

Important! Always use a top-down lighting. The stove is constructed

for this in order to give the best exploitation."Top down" lighting is

a more environmentally friendly way of lighting the fire and helps to

keep the glass area as clean as possible.

2 pieces of wood approx. 20-25 cm long with a weight of approx.

0.5–0.6 kg per piece (image 1)

The wood must not cover the bottom entirely and must never be

placed higher than the Clean-Burn rail at the rear of the stove.

1 pieces of wood approx. 0.3–0.4 kg (image 2) 8-12 thin sticks of about

20 cm with a total weight of approx. 0,5 kg (image 3-5).3 fire starters.

Place logs, sticks and fire starters in the combustion chamber as

shown on images 1-5.

Set the primary and secondary air controls to maximum in the

lighting phase. If the fire is too strong, you may throttle down the

primary air damper (at the left).

INSTRUCTIONS FOR HEATING

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Scan 66 series Seite 30

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Scan 66 series

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info