Bedienungsanleitung Scan 68 (Seite 33 von 48) (Englisch)

745571

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

INSTRUCTIONS FOR USE

CB-TECHNOLOGY (CLEAN BURN)

The stove is equipped with CB technology. In order to ensure optimal combustion of gases released during the combustion

process, air passes through a specially developed system of channels. The heated air is conducted into the combustion chamber

through the holes in the rear lining of the combustion chamber and at the bafﬂe plates. This airﬂow is controlled by the rate of

combustion and cannot therefore be regulated.

NOTE: The wood must never be placed higher than the tertiary holes at the rear of the burn chamber (This does not apply at a

cold start).

BAFFLE PLATE

The bafﬂe plate is located in the upper part of the combustion chamber. The plate holds back smoke, making sure it stays inside

the combustion chamber for a longer time before escaping through the chimney. This reduces the ﬂue gas temperature as the

gases have more time to dissipate heat to the stove.

The bafﬂe plate must be removed for sweeping; see “Maintenance”. Note that the bafﬂe plate is made of porous, ceramic materi-

al, and is liable to break easily. You should therefore handle it with care.

The bafﬂe plate is subject to wear and tear and not covered by the warranty.

PRIMARY AIR

The primary air is used when lighting the stove and must be closed after 10-20 minutes, when the ﬁre has caught well. The prima-

ry air can be used continuously when using very hard wood.

Settings for normal load: 0 - 30%

SECONDARY AIR

Secondary air is pre-heated and fed indirectly to the ﬁre. At the same time, the secondary airﬂow cleans the glass pane to avoid

soot build-up. If you over-restrict the secondary airﬂow, soot can build up on the glass pane. The secondary airﬂow determines

the heat output from your wood stove.

Settings for normal load: 50 - 70%

ASH CONTAINER

¬ Open the door of the stove to access the ash container under the combustion chamber.

¬ The ash container must always be closed during operation.

¬ The ash container must not be overﬁlled and must therefore be emptied at regular intervals.

THE CLEAN AIR ACT 1993 AND SMOKE CONTROL AREAS

Under the Clean Air Act local authorities may declare the whole or part of the district of the authority to be a smoke control area.

It is an offence to emit smoke from a chimney of a building, from a furnace or from any ﬁxed boiler if located in a designated smoke

control area. It is also an offence to acquire an "unauthorized fuel" for use within a smoke control area unless it is used in an "ex-

empt" appliance ("exempted" from the controls which generally apply in the smoke control area).

The Secretary of State for Environment, Food and Rural Affairs has powers under the Act to authorize smokeless fuels or ex-

empt appliances for use in smoke control areas in England. In Scotland and Wales this power rests with Ministers in the devolved

administrations for those countries. Separate legislation, the Clean Air (Northern Ireland) Order 1981, applies in Northern

Ireland. Therefore it is a requirement that fuels burnt or obtained for use in smoke control areas have been "authorized" in Regu-

lations and that appliances used to burn solid fuel in those areas (other than "authorized" fuels) have been exempted by an Order

made and signed by the Secretary of State or Minister in the devolved administrations.

¬ Further information on the requirements of the Clean Air Act can be found here: http://smokecontrol.defra.gov.uk/

¬ Your local authority is responsible for implementing the Clean Air Act 1993 including designation and supervision of smoke

control areas and you can contact them for details of Clean Air Act requirements”

¬ The secondary air valve has been modiﬁed, so that is does not close completely but has an opening corresponding to the posi-

tion used at the lowest emission test.

¬ You can use any type of wood as fuel.

¬ This stove has been recommended as suitable for use in smoke control areas when burning wood.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Scan 68 Seite 33

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Scan 68

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info