Bedienungsanleitung Scan DSA 12 (Seite 7 von 20) (Englisch)

745587

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

ASSEMBLY

Before installing the stove

Load-bearing foundation

All items in our product range come under the category of light-

weight fireplaces and stoves and do not normally require any rein-

forcement of the beam structure. They can be positioned on ordinary

beams/floor.

You should of course make sure that the foundation on which the

stove is positioned can indeed support the weight of the stove and,

where applicable, a steel chimney, if you have opted for this solution.

In case of doubt about the carrying capacity of the floor, please con-

sult a building expert.

Floor plate

The national and local building regulations must be followed regar-

ding the size of a non-flammable base which is to cover the floor in

front of the built-in stove.

Your local Scan dealer can give guidance on the rules concerning the

protection of flammable material around the stove.

The floor plate’s function is to protect flooring and flammable mate-

rial against any embers.

A floor plate can be made of steel or glass, however clinker tiles, natu-

ral stone or similar materials can also be used.

If you have chosen to install the Scan DSA 12 on flammable material, it

is a legal requirement that steel floor plates be used on both sides of

the stove. One door can be locked, and in such cases a steel floor plate

need only be installed on the side on which the door can be opened.

Convection air

Holes for convection air must be made in the surround. Convection

means that air circulation occurs, so that the heat is distributed more

evenly around the room.

It is advisable to make holes for convection on both sides of the sur-

round.

You must ensure that the requirements for convection areas are met.

Area for convection air in: 350 cm2

Area for convection air out: 500 cm2

If insufficient convection is created, the sorround may be damaged.

Distance to furniture: 1200 mm

But please check to avoid furniture or other furnishings being dried

out due to being too close to the stove.

Installation in connection with flammable

materials

See pages 9 and 10.

Positioning near non-flammable materials

When building or fitting into structures that do not contain flam-

mable materials, a minimum distance of 10 mm must be maintained

between the brickwork and the convection hood. This is to prevent

cracks in the brickwork caused by the expansion of the metal while

the stove is heating. This construction does not require convection

grates except for the convection air produced by the convection box of

the insert. However, please note that without convection grates, the

effect of the insert will be lower.

Trims and doors

Trims and doors are fitted when the surfaces of the surround have

been treated.

NAVN:

STI:

DIMENSION:

MATERIALE:

DATO:

SIGN:

Krog Iversen & Co A/S

DK-5492 Vissenbjerg©

TG.NR:

EMNE:

I:\Udvikling\TEGNING\DSA 12\90085017.idw

90085017

Billede indbygning

29-01-10

Scan DSA 12

VÆGT:

AREAL:

N/A

Ash drawer

Note! The ash drawer can only be used from one side. The door on the

opposite side of the ash drawer can be locked.

Existing chimney and pre-fabricated element

chimney

If you intend to connect your stove to an existing chimney, it makes

sense to contact an authorised Scan dealer, or a local chimney sweep

for advice. These experts will also let you know if your flue needs

renovating.

When connecting a pre-fabricated element chimney, follow the

manufacturer’s connection instructions for the relevant chimney

type.

Connection between stove and steel chimney

Your Scan dealer, or local chimney sweep, can advise you on choosing

a make and type of steel chimney. This ensures that the chimney will

match your wood-burning stove. We recommend that the chimney’s

length from the top of the stove should be no less than 4.5 metres.

Some weather or installation conditions might require another

length.

Choosing the wrong length or diameter of steel chimney could

impair functionality.

Always observe the chimney vendor‘s instructions precisely.

Requirements for chimney

The chimney must be labelled T400 and G for soot testing.

If the chimney is installed as an extension of the stove and has a

length of at least 4.5 metres, a 6" chimney can be used.

If the stove is installed with elbow pipes or other bends in the chim-

ney, a 7" chimney can be used.

The use of a curved elbow pipe is recommended, as it will give a bet-

ter draught.

If you are connecting your stove using a sharp elbow bend, the clea-

nout door should be in the vertical section, such that the horizontal

part can be cleaned through it.

Safety distance

European, national and local regulations concerning safety distances

for wood-burning stoves and flue pipes must be complied with.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Scan DSA 12 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Scan DSA 12

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info