Bedienungsanleitung Scheppach AB1600 (Seite 13 von 44) (Deutsch, Englisch, Holländisch, Französisch)

781659

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite

13GB

plete stop before placing it down. The tool insert can

jam and lead to loss of control over the power tool.

Technical data

Mains voltage: 230V / 50Hz

Power input: 1050W

Idling speed: 480 min-1

Impact rate: 3780 bpm

Drilling capacity

in concrete/stone

(max.):

38 mm

Protection class: II

Weight: 6 kg

Sound and vibration

Sound and vibration values were measured in

accordance with EN 60745.

Sound pressure level Drilling LpA 93,8 dB(A)

Sound pressure level Chisel LpA 95,8 dB(A)

Uncertainty KpA 3 dB

Sound power level Drilling LWA 104,8 dB(A)

Sound power level Chisel LWA 106,8 dB(A)

Uncertainty KWA 3 dB

Wear ear-muffs.

The impact of noise can cause damage to hearing.

Total vibration values (vector sum of three directions)

determined in accordance with EN 60745.

Vibration emission value ah (Handle)

= 14,89 m/s2

Vibration emission value ah (Additional Handle)

= 13,02 m/s2

Uncertainty K = 1,5 m/s2

Additional information for electric power tools

Warning!

The specied vibration value was established in ac-

cordance with a standardized testing method. It may

change according to how the electric equipment is

used and may exceed the specied value in exceptio-

nal circumstances.

The specied vibration value can be used to compare

the equipment with other electric power tools.

The specied vibration value can be used for initial as-

sessment of a harmful effect.

Keep the noise emissions and vibrations to a mi-

nimum.

• Only use appliances which are in perfect working

order.

• Service and clean the appliance regularly.

• Adapt your working style to suit the appliance.

• Do not overload the appliance.

• Have the appliance serviced whenever necessary.

• Switch the appliance off when it is not in use.

• Wear protective gloves.

Residual risks

Even if you use this electric power tool in ac-

cordance with instructions, certain residual risks

cannot be rules out. The following hazards may

arise in connection with the equipment’s construc-

tion and layout:

• Lung damage if no suitable protective dust mask is

used.

• Damage to hearing if no suitable ear protection is

used.

• Health damage caused by hand-arm vibrations if the

equipment is used over a prolonged

Before starting the equipment

Before you connect the equipment to the mains supply

make sure that the data on the rating plate are identi-

cal to the mains data.

Always pull the power plug before making adjustments

to the equipment.

Check the drilling point for concealed electrical cables,

gas and water pipes using a cable/pipe detector.

Additional handle (Fig. 2 – Item 6)

For safety reasons you must only use the hammer drill

with the additional handle.

The additional handle (6) enables you to achieve bet-

ter stability whilst using the hammer drill. The machine

must not be used without the additional handle (6) for

safety reasons.

The additional handle (6) is secured to the hammer

drill by a clamp. Turning the handle anti-clockwise

(looking from the handle) will release the clamp. Tur-

ning the handle clockwise will tighten the clamp. First

release the additional handle clamp. You can then

swing the additional handle (6) into the most comfor-

table working position for you. Now turn the additional

handle in the opposite direction again until the additio-

nal handle is secure.

Tool insertion (Fig. 3)

• Clean the tool before insertion and apply a thin coa-

ting of drill bit grease to the shaft of the tool.

• Pull back and hold the locking sleeve (2).

• Insert the dust-free tool into the tool mounting as far

as it will go whilst turning it. The tool will lock itself.

• Check that it is properly secure by pulling the tool.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Scheppach AB1600 Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Scheppach AB1600

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info