Bedienungsanleitung Scheppach AB1600 (Seite 14 von 44) (Deutsch, Englisch, Holländisch, Französisch)

781659

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite

14 GB

Tool removal (Fig. 4)

Pull back and hold the locking sleeve (2) and remove

the tool.

Dust collection device (Fig. 5)

Slide the dust collection device (a) over the drill bit be-

fore carrying out any hammer drilling vertically above

your head.

Starting up

Important.

To prevent all danger, the machine must only be

held using the two handles. Otherwise there may

be a risk of suffering an electric shock if you drill

into cables.

Switching on and off (Fig. 1)

To switch on: Press the control switch (4).

To switch off: Release the control switch (4).

Setting the operating mode (Fig.6)

The operating mode of the power tool is selected with

the mode selector switch

Note: Change the operating mode only when the

machine is switched off! Otherwise, the machine can

be damaged.

– Turn the mode selector switch to the requested

position.

• Position for hammer drilling (A): When the drilling

tool does not immediately rotate upon switching on,

allow the machine to run slowly until the drilling tool

rotates.

• Vario-Lock (B) position for adjustment of the

chiselling position

• Position for chiselling (C)

Important.

Only low pressure is required for hammer dril-

ling. Excessive pressure will exert an unnecessary

force on the motor. Check the drill bits at regular

intervals. Sharpen or replace blunt drill bits.

Replacing the power cable

If the power cable for this equipment is damaged, it

must be replaced by the manufacturer or its aftersales

service or similarly trained personnel to avoid danger.

Cleaning and maintenance

Always pull out the mains power plug before starting

any cleaning work.

Cleaning

• Keep all safety devices, air vents and the motor

housing free of dirt and dust as far as possible. Wipe

the equipment with a clean cloth or blow it with com-

pressed air at low pressure.

• We recommend that you clean the device immediately

each time you have nished using it.

• Clean the equipment regularly with a moist cloth and

some soft soap. Do not use cleaning agents or sol-

vents; these could attack the plastic parts of the equip-

ment. Ensure that no water can seep into the device.

Carbon brushes

In case of excessive sparking, have the carbon brushes

checked only by a qualied electrician. Important! The

carbon brushes should not be replaced by anyone but

a qualied electrician

Maintenance

There are no parts inside the equipment which require

additional maintenance.

Disposal and recycling

The unit is supplied in packaging to prevent its being

damaged in transit. This packaging is raw material and

can therefore be reused or can be returned to the raw

material system.

The unit and its accessories are made of various types

of material, such as metal and plastic. Defective com-

ponents must be disposed of as special waste. Ask your

dealer or your local council.

Storage

Store the equipment and accessories out of children’s

reach in a dark and dry place at above freezing tempe-

rature. The ideal storage temperature is between 5 and

30 °C. Store the electric tool in its original packaging.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Scheppach AB1600 Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Scheppach AB1600

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info